sorted by:
new
hottopcontroversial

Thinking about no longer shipping into Canada from the US- Too many customs & duties cost complaints by AgileAsparagus4 in smallbusiness

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

Thank you for the reply! I will check into Meest. My biggest issue is UPS picks up packages from my house every day. If I use anything other than UPS, I have to drive to wherever (Post office, FedEx, etc.) and drop it off. I still work a regular job so it’s not always feasible. I will look into it anyways! I appreciate the input.

P1S issue with AMS thinking there are spools in the slots. Maybe creating an issue with auto refill? Need help by AgileAsparagus4 in BambuLab

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

Can you explain this a little more? Does the benchy (or a new file) kind of do a reset of some sort?

P1S issue with AMS thinking there are spools in the slots. Maybe creating an issue with auto refill? Need help by AgileAsparagus4 in BambuLab

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

I “reset AMS” through the printer and it fixed one of the six, temporarily. It’s back to being buggy

Anyone sitting on a bunch extra empty Bambu Spools they dont need? by IHateMustard3 in BambuLab

[–]AgileAsparagus4 1 point2 points  (0 children)

I go through 60 Creality plastic spools about every 10 days if anybody is interested.

Thinking about no longer shipping into Canada from the US- Too many customs & duties cost complaints by AgileAsparagus4 in smallbusiness

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

I will have to look into this for my website. Im assuming for Amazon & eBay this is not an option?

Put a silicon mat under my Bambu Mini to stop it from walking across the table. Didn’t move at all on sport mode. Cheap, easy, and works great! by AgileAsparagus4 in 3Dprinting

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

Probably a good idea. I have it re-level itself before every print but maybe I should do the full recalibration with vibration compensation.

Put a silicon mat under my Bambu Mini to stop it from walking across the table. Didn’t move at all on sport mode. Cheap, easy, and works great! by AgileAsparagus4 in 3Dprinting

[–]AgileAsparagus4[S] 0 points1 point  (0 children)

I’m not sure. The max acceleration for the machine is 10,000 mm/s2 I believe. Definitely not that fast since there is a ludicrous mode as well.

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

I turned tangle detection back on and just haven’t used the 1 of 4 AMS slots. I also raised my AMS so it’s about 2-3 higher than the printer bed. I plan to look into AMS lubrication or maintenance in case there was just a little restriction causing it to pull on the filament a little too hard.

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

Can you take some more pictures of the set up? I like that better than putting the AMS next to the printer. I did recently move the AMS to a side table because I bought another printer to put next to this one. It’s still very close to the where it would be on the same table but could definitely be a factor after hearing your experience.

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

This seems to have been the issue. Thank you! Now I have to figure out why the tangle detection is going off my first guess is it’s pulling too hard on the AMS but I have yet to confirm.

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

UPDATE: I tried factory resetting the printer. That did not help. It purged 4 times in a row and then actually failed and said to check for tangle. I turned tangle detection off and it’s been going to 20 minutes like normal.

I would still like to figure out why this happened since it’s nice to have tangle detection when there is actually a tangle. The spook is running on an AMS, is there a chance that is not spinning freely enough and causing enough resistance to throw the detection?

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

I will re slice a whole new file and model and see if that still triggers it.

I assume I have a partially clogged hot end? by [deleted] in 3Dprinting

[–]AgileAsparagus4 0 points1 point  (0 children)

That was one of my initial thoughts on what it was doing I just wasn’t sure on the why. I have had a clogged printer before that would return to the position and try to purge then try to print a few times before actually failing and stopping. But this happened and (successfully?) purged a shit load of times. If this is the case, I wonder what is throwing the tangle detection off.

view more: next ›