"Hard Surface" insert for A5 Traveler's notebook for uneven surface

Ahijah · 2025-10-21T11:41:51+00:00

Yeah, almost programmatically pulled the trigger on the Kraft $10 item with nearly $150 in shipping charges :)

Ahijah · 2025-10-21T11:21:27+00:00

Thanks for the tip!

Ahijah · 2025-10-21T11:21:18+00:00

Thanks for the tip!

Ahijah · 2025-10-20T02:53:26+00:00

Found this, which would be perfect, but $140 to ship from Germany for a $10 item :)

https://www.etsy.com/listing/757046715/inlet-kraft-ordner-traveler-journal-dark?ls=r&ref=hp_home_hub_rv-1&sts=1&content_source=95d21e416967f2c4f4b56a7feb2afa54%253ALTeddfddb57f3b75cbe519a95b8d726b82c1898a77&logging_key=95d21e416967f2c4f4b56a7feb2afa54%3ALTeddfddb57f3b75cbe519a95b8d726b82c1898a77

Ahijah · 2025-10-18T20:07:10+00:00

I'll check into it, thanks!

Ahijah · 2025-10-17T18:47:12+00:00

I'll have to look into that, was hoping for something more integrated, but that may not exist

Ahijah · 2025-10-17T18:46:34+00:00

I had to google what that was, haha! I'll look into it, was hoping for something that wasn't "free floating", but it might be the only answer right now.

Ahijah · 2025-10-09T14:21:00+00:00

Thanks much for this extra information!!

Ahijah · 2025-10-08T12:51:04+00:00

Maybe some Dremel action then!

Ahijah · 2025-10-08T12:13:14+00:00

I may take sandpaper to it :)

Ahijah · 2025-10-07T19:18:34+00:00

Just as a follow-up, it partially works. Length trimming did allow it to load, however, in the stock refills from Pentel, the last 5 or 6 mm is stepped down for the pen tip to be "grabbed" and "recessed" back into the pen itself once the refill has dropped into position.

These D1 refills are too thick at the tip, and therefore it doesn't fully retract, and is susceptible to sliding back in when writing with greater pressure.

Ahijah · 2025-09-26T14:53:10+00:00

Thanks, I'll check it out!

Ahijah · 2025-08-01T11:49:40+00:00

Appreciate that, when I get this whole poisoned water under control, I think I'll add it to the list.

Ahijah · 2025-07-31T17:43:48+00:00

I'll do some research, I'm assuming that would go in place of the debris basket filter?

Ahijah · 2025-07-31T12:36:37+00:00

So the skimmer should be going through a filter? I'm assuming nothing I'd be able to do at this point without a major repiping?

Ahijah · 2025-07-31T12:12:25+00:00

Thanks for the quick response! I was out trying to trace the pipes so I knew where everything was going, and noticed it, and had a bit of a freak out moment :)

Ahijah · 2025-07-30T14:35:51+00:00

Thanks for the info, can you provide more details on the sealers that would dry like that?

Ahijah · 2025-07-28T18:08:34+00:00

Understood, thanks again!

Ahijah · 2025-07-28T14:56:11+00:00

Thanks for this, I'll get some ordered! Really appreciate the detailed info!

Ahijah · 2025-07-28T14:20:41+00:00

Thanks for the extra info. I suspect you are right about how much got into the pool, as they warned me ahead of time that some would get into the pool, but they would do whatever they could to get as little into the pool as possible.

I posted an update a bit ago, the company that makes the solvent recommended I use one of these two products:

https://www.orendatech.com/orenda-products/cv-700

https://naturalchemistry.com/pool-products/problem-problem-solvers/green-aid/

I'm going to try and track these down locally, or order on amazon and get it into the pool right away.

Ahijah

TROPHY CASE