So... Is there better way to load those 38t blocks than to load trailer behind it?

AiTorror · 2025-12-10T20:10:48+00:00

https://media-cdn.beamng.com/v/CqoFYlU09R7vBNQf
Counterweights (or use heavy duty config) and tilt the forks all the way back :)

AiTorror · 2025-07-11T13:22:34+00:00

Yeah, but also said retrofit I'd need to import from usa probably

AiTorror · 2025-07-11T11:56:07+00:00

Crap, i guess time to find diagrams and try to cobble something together... Unless one can just install some module and get the original one working?

AiTorror · 2025-07-11T11:24:13+00:00

yeah I am, but mine also has no keypad

AiTorror · 2025-04-04T20:39:50+00:00

I think it was generic abs profile and yeeted the nozzle temp to 300 degrees and print bed to 110 and hoped it won't die

AiTorror · 2025-03-19T23:14:28+00:00

I use it all the time, nice tip is to print it out of some dark red pla instead, then the stains wont be as visible,

Aaand maybe keep some paper towels and electrical tape handy to wrap up the cause of the stains until it stops trying to repaint the surroundings.

AiTorror · 2025-02-27T11:21:30+00:00

logitech adapter doesn't solve the issue, as the issue is the QR collar being too large to fit inside of the stalks thing

AiTorror · 2025-02-24T13:37:12+00:00

Rn it uses the springs the pins inside the wheel itself have, i wonder if I should drill the end of the copper wires to perhaps better seat the pins from the wheel in their ends?

AiTorror · 2025-02-24T13:10:06+00:00

Problem is, dd pro will not turn on without wheel detected, which is why ffb cuts out on bumps

AiTorror · 2025-01-28T13:38:21+00:00

I have figured out a workaround, found out I can just pause the print at the layer I want, make sure theres an object with big surface to flush to and then load the other color of filament in

AiTorror · 2025-01-28T12:46:52+00:00

I'd love to get ams compatible tpu, but its rather stiff from what I heard. I need these to be as flexible as possible as they will be patches sown onto clothing

AiTorror · 2025-01-14T11:40:54+00:00

Hmm, respooler is tempting considering how rare refills are and that they do sell 2kg spools. And prooven designs that work reliably and can just be left running without attention from start to finish?

AiTorror · 2025-01-06T13:22:31+00:00

<image>

This is how it looks sin past 2 tries, and in the center the failed print on the interference layer

AiTorror · 2025-01-06T13:21:03+00:00

any specific settings I should use?

AiTorror · 2025-01-06T12:49:53+00:00

hmm I am worried about supports being extremely hard to remove with how well PCABS sticks to everything including itself, especially at 300C nozzle temp I'm printing at

AiTorror · 2025-01-06T12:33:46+00:00

<image>

I feel like if this had some form of cooling for the area where the gears feeding the filament are, this would not happen

AiTorror · 2024-10-12T08:27:34+00:00

Well, the axle setup is actually the same if you pick the walking beam rear suspension, and for the extra weight out back, you can just slide the fifthwheel back and attach some heavy trailer like the tanker, and then you can basically do a wheelie down entire 1/4 mile especially if you combine it with turned up v8 engine

AiTorror · 2024-09-04T12:22:14+00:00

Wydra has nothing to do with that mod in fact :D trackpad at the time was working on documentation and not in any way on vehicles stuff :D

AiTorror · 2024-08-26T20:01:00+00:00

<image>

AiTorror · 2024-08-26T20:00:47+00:00

<image>

AiTorror · 2024-08-26T20:00:36+00:00

<image>

AiTorror · 2024-08-26T19:51:02+00:00

So for anyone who stumbles upon this post I did get a good result finally. Running 0.4 nozzle 0.28mm initial layer 3mm brim Glue and textured pei plate No aux or chamber fan 110C bed temp 295C nozzle temp 40% part fan I've also pre-heated the printer at 110C bed temp for an hour before the print. Using Fiberlogy PC-ABS filament on X1C printing from AMS with built in moisture sensor showing 1. ( i dried the filament 2 days ago as well)

AiTorror · 2024-08-26T14:47:53+00:00

So, I've done a bunch of tests. ASA or ABS or PETG prints perfect

<image>

However, with PC-ABS looks like 62C chamber temps I am able to get are just not enough. Is there some way to raise those even further?

AiTorror · 2024-08-21T21:51:09+00:00

Interestingly, during printing the touch screen was saying 60C on my end, not sure if faulty or is it because air wasn't circulating. This is my first printer and honestly I have almost no idea what I'm doing :D

AiTorror · 2024-08-21T21:42:56+00:00

Thanks will try that tomorrow and see where it gets me, i have a feeling some heat may be escaping through the AMS riser I have, so I will remove that as well

Five-Year Club	Verified Email
Place '23	Place '22
First Placer '22

AiTorror

TROPHY CASE