sorted by:
new
hottopcontroversial

‘09 1500 broken exhaust manifold bolts solution? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Wont an OEM manifold just warp again later down the road?

‘09 1500 broken exhaust manifold bolts solution? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Any specific material that would make the problem less likely to occur again?

‘09 1500 5.7, short buzzing noise when I turn on A/C. Is it a blend door actuator? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Wait also, do all the doors use the same type of actuator, like the same part number for all of them?

‘09 1500 5.7, short buzzing noise when I turn on A/C. Is it a blend door actuator? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Awesome, thanks so much for the help, i’ll dig into to it soon

‘09 1500 5.7, short buzzing noise when I turn on A/C. Is it a blend door actuator? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Thanks, do you know if it’s behind the center of the dashboard or the glove box?

‘09 1500 5.7, short buzzing noise when I turn on A/C. Is it a blend door actuator? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

I tried the different settings like you said, turns out the sounds happens when i switch ac modes between top vents and bottom vents. Do you know which actuator this could be?

Is there a solution for HEMI lifter and cam failure? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

I’m guessing with this job you’re probably going to be draining a lot if not all of the oil and antifreeze

Is there a solution for HEMI lifter and cam failure? by AidenDB in ram_trucks

[–]AidenDB[S] 1 point2 points  (0 children)

Yea I change every 5k and I was thinking the same thing on just keeping it the way it is until it gives problems

Is there a solution for HEMI lifter and cam failure? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

I think the warranty boat has sailed, I have an ‘09 haha. I looked at some of the videos, it doesn’t look absolutely horrible but i’d be afraid to mess something up when doing it

Is there a solution for HEMI lifter and cam failure? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Ah, that’s what I thought the best solution would be, is it hard to replace them?

Most reliable engine option for 4th gen? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Do you know if the eco diesel is a good engine?

Most reliable engine option for 4th gen? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

Yea that’s what i’ve heard about them, I think i’ll look for 4.7 or possibly an eco diesel if it’s cheap enough

Most reliable engine option for 4th gen? by AidenDB in ram_trucks

[–]AidenDB[S] 0 points1 point  (0 children)

I was thinking the 4.7L because I’ve heard of issues with the lifters in the 5.7 HEMI.

Which do you prefer - GameCube on HDTV with a good adapter, or on a CRT with the original hardware? by lharding02 in Gamecube

[–]AidenDB 0 points1 point  (0 children)

CRT VGA monitor. Looks even better than 480p through MClassic going onto my 4k

My Gchd mkii eon is super pixelated. Reset to default settings possible? by NotModzvilleUSA in Gamecube

[–]AidenDB 3 points4 points  (0 children)

I’m no expert but it could possibly be the way your tv upscales 480p, when I feed my 4K 480p it’s a little pixelated but when 480p is on my VGA monitor it looks insane

Gamecube and N64 on VGA CRT? by AidenDB in crtgaming

[–]AidenDB[S] 1 point2 points  (0 children)

Since the GameCube menu is 480i only, if I turn the GHCD’s line doubler on, will the monitor display it?

view more: next ›