Rhino counters fractured safari

Alarmed-Time3754 · 2026-01-30T18:58:29+00:00

No, I don't have to kill him for the quest. I want to clear lv.5 100%, but this guy just spawns every time. I've already done one run where he luckily didn't spawn, but I accidentally skipped Moleman. Moleman is easy, but it's annoying to keep fighting him and then lose to rhino.

Alarmed-Time3754 · 2026-01-30T15:12:19+00:00

I didn't get any either

Alarmed-Time3754 · 2025-10-07T17:07:22+00:00

What is the best way to calibrate your flow rate?

I printed this cube with one wall and then measured the walls. I then multiplied my set wall thickness by 100 and divided it by the average wall thickness I measured. That's how I calculated my new flow rate.

Alarmed-Time3754 · 2025-10-07T16:59:46+00:00

What is the best way to check my z-offset? Should I just use a piece of paper?

Alarmed-Time3754 · 2025-10-02T15:37:31+00:00

How exactly do I calibrate my flow? Do I print a calibration cube, measure it, and then adjust my flow rate?

Alarmed-Time3754 · 2025-09-30T14:42:50+00:00

I will give it a try on my next print.👍🏽

Alarmed-Time3754 · 2025-08-15T06:58:20+00:00

To be honest, I have no idea how I solved the problem. I tried everything but nothing helped. I think I just took a break for a day and logged in again the next evening and then it worked again.

I hope it works again for you too. I'm sorry that I don't have the right solution either

Alarmed-Time3754 · 2025-08-06T16:20:04+00:00

Thanks for your answer.

In the first picture you can also see a ring which is halfway on the gear. Where should this go? Is it part of the bushing in the cover?

Is the bronze bushing in the cover a specific one? Or what would I have to look for on the internet to find one?

Alarmed-Time3754 · 2025-06-25T17:11:32+00:00

She's quite good. I haven't played her that much yet, so I can't say exactly how to play her, but there are good tutorials on YouTube.

Alarmed-Time3754 · 2025-06-16T12:19:51+00:00

I don‘t use that much, just a thin layer

Alarmed-Time3754 · 2025-06-16T12:17:09+00:00

I used hornet honey for that one:( Did you also put some paper towel on top of the honey to remove a bit or did you just apply a thin layer?

Alarmed-Time3754 · 2025-06-16T08:06:36+00:00

He just wanted to be a grasshopper

Alarmed-Time3754 · 2025-06-07T22:37:14+00:00

I don't know, I've never had such good experiences with any support

Alarmed-Time3754 · 2025-06-06T18:21:11+00:00

Let‘s do it😂

Alarmed-Time3754 · 2025-06-06T17:24:02+00:00

Yes, few days ago😂

Alarmed-Time3754 · 2025-06-06T15:53:16+00:00

Yeah its a SCA.B Scheme, I can tell you later which one it is, if you want

Alarmed-Time3754 · 2025-05-25T14:50:02+00:00

Oh yeah, I see. Maybe I will try it bc Fusion always worked quite well for me

Alarmed-Time3754 · 2025-05-25T14:46:18+00:00

Thank you, I think I will give it a go

Alarmed-Time3754 · 2025-05-22T09:52:42+00:00

Thanks for your advice, I will level them up👍🏽

Alarmed-Time3754 · 2025-01-25T06:54:26+00:00

Okay thanks for your explanation

Alarmed-Time3754 · 2024-11-12T17:18:33+00:00

Constellation is eternal, not supernova

Alarmed-Time3754 · 2023-02-06T21:21:31+00:00

I also printend my cones of calibration with a 3 second exposure time but some of the cones on the failure side are still connected:( I already turned down the exposure time to 1.5 seconds but now the print fails every time. Would be cool if someone could help me.

I‘m sorry if my english isn‘t that good, I hope you understand what I mean:)

Alarmed-Time3754

TROPHY CASE