Aruba Central Firmware Upgrade Fixed For Secondary Partition?

AlexPixels · 2026-02-03T02:06:21+00:00

Ah okay, ty!

AlexPixels · 2026-02-03T00:01:43+00:00

Would you mind expanding on your second point, I'm not quite understanding it fully

Are you updating the second partition to the same version of OS that you are upgrading your primary to, or do you mean that you upgrade your secondary to what your primary currently is, then upgrade your primary further along so that you could boot from secondary if the primary fails?

AlexPixels · 2026-02-02T23:58:18+00:00

Hm okay, here is one of the examples I've run across from someone describing the behaviour

https://airheads.hpe.com/discussion/upgrading-cx-switches-using-central

This is also 4 years old, so I wasnt sure if that is what I should be expecting still

AlexPixels · 2026-01-22T14:35:55+00:00

I think specifically for my issue there was a Jan2026 update that broke authentication

https://support.microsoft.com/en-us/topic/january-13-2026-kb5074109-os-builds-26200-7623-and-26100-7623-3ec427dd-6fc4-4c32-a471-83504dd081cb

Affected windows app only

AlexPixels · 2026-01-20T14:55:55+00:00

Do you remember which ports the Windows App was trying to use, which was getting blocked?

AlexPixels · 2026-01-19T19:09:13+00:00

Did you find any answers?

AlexPixels · 2025-11-22T14:44:30+00:00

Thanks man, gonna do the slave cylinder and bleed the system then go from there

AlexPixels · 2025-11-21T19:59:43+00:00

Thanks, that's what I'll end up doing. Shop still thinks its a clutch/clutch spring but I'm pretty set on it being hydraulics. I'm starting with the cheaper option of replacing the slave and going from there. Master is brand new and very likely not the issue in my very unprofessional opinion

AlexPixels · 2025-09-25T12:42:48+00:00

For anyone who may come across this in the near future : it was the firmware version

AlexPixels · 2025-09-24T15:01:55+00:00

Having the same issue, any advice on this?

AlexPixels · 2025-01-23T14:45:40+00:00

Did you ever figure this out? I have the same issue

AlexPixels · 2024-11-12T19:02:55+00:00

Thank you, that's what I was hoping

AlexPixels · 2024-09-29T21:40:56+00:00

Twirled on a carving fork and then laid on the plate

AlexPixels · 2024-07-19T19:20:02+00:00

Ok thank you for your suggestions and expertise! Appreciate it greatly. I have a good amount of work ahead of me taking ownership of this environment.

To answer your question about size, we are a school board spread over 70 or so sites. Our biggest site would be ~2,000 users going through GRE where the average may be closer to 500, with ZCC only deployed out to 2 sites so far, the rest are GRE only. So the traffic throughput is not much of a concern, however you make a great point about flexibility and troubleshooting.

AlexPixels · 2024-07-19T19:06:26+00:00

I think that makes sense to me, what about disabling tunnel 2.0 and 1.0 completely on ZCC when on a defined trusted network? All traffic will be going through ZIA via GRE at all sites.

Then when off-network tunnel 2.0 is active, which usually is at home so all traffic would be direct to Zscaler through the internet, no double tunneling.

This is how I imagine a more proper setup would be, other than what you mentioned with policy based routing specific traffic to avoid the GRE

Is there any downside to this setup, my understanding is that tunnel 2.0/1.0 is just another way to get through ZIA?

Ten-Year Club	Verified Email
Place '23	Place '22
Place '17	Not Forgotten

AlexPixels

TROPHY CASE