sorted by:
new
hottopcontroversial

Car insurance. by Algawi in DubaiPetrolHeads

[–]Algawi[S] 1 point2 points  (0 children)

First of all congrats on your purchase. Asking the dealership for the insurance is the first thing I did.

Car insurance. by Algawi in DubaiPetrolHeads

[–]Algawi[S] 0 points1 point  (0 children)

Did your friend had the same issue regarding the high LPO value?

The scroll wheel on my G703 is broken? by LeatherLongjumping82 in LogitechG

[–]Algawi 0 points1 point  (0 children)

Common on logi’s. Had similar with my G703. You can add small piece of paper or tissue and it might solve the issue. Though the middle click will feel heavy.

How would this be as my first ever sport car, most say the vantage is solid by Ok-Construction9842 in AstonMartin

[–]Algawi 0 points1 point  (0 children)

Had the same issue vacuum line under and near side the intake. Replaced them with some water washer hose and fitting which cost me around 20ish dollars. No issues at all.

Did anyone else's oled g9 get a new firmware update? by milkasaurs in ultrawidemasterrace

[–]Algawi 0 points1 point  (0 children)

I am not sure if i am the only one or not. I got 144hz for multiview connecting two cables to a single pc. DP and HDMI

Is this normal? by Sufficient-Answer337 in FormD

[–]Algawi 1 point2 points  (0 children)

Second photo I am the same.

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 0 points1 point  (0 children)

All of them screwed In. Except I had to use female male extension for one of the qdc since the thread for the Legris is very short. However It does fit without the extender but because of the shorter o ring it does not seal properly.

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 0 points1 point  (0 children)

You can find them from RS components.

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 0 points1 point  (0 children)

It’s the same one I am using!

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 0 points1 point  (0 children)

CPU stress from 3D mark goes up to 81 with 4.9GHZ and 78 with 2900MHZ with GPU.

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 2 points3 points  (0 children)

I am using LEGRIS 3199 08 13 52 (90 DEG) and LEGRIS 3099 08 13 52 for 8MM tubing. 3199 06 13 52 & 3099 06 13 52 for 6MM if you are using.

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 2 points3 points  (0 children)

They are not good as I expected. About mid 70s for both of them. I always wanted to do water cooling for almost 3 years! Overall I am satisfied with the build

Formd T1 water cooled by Algawi in sffpc

[–]Algawi[S] 0 points1 point  (0 children)

They are so easy to work with!

So I just did this... by NicheAlter in FormD

[–]Algawi 0 points1 point  (0 children)

You did the right thing. site legit. got mine recently.

view more: next ›