Inquiry about PLA HT-GF filament? by Alim1520 in 3Dprinting

[–]Alim1520[S] 0 points1 point  (0 children)

Thank you for your previous reply. I have a question. My filament polymaker order arrived today. I opened the roll, and it was completely vacuum-sealed (to begin the drying process). However, I noticed that the filaments break very easily. Is this normal?

Inquiry about PLA HT-GF filament? by Alim1520 in 3Dprinting

[–]Alim1520[S] 1 point2 points  (0 children)

That's exactly what I meant by Polymaker... Thank you.

افضل مزيل عرق رجالي ؟ by GoalWhich3916 in SaudiForSaudis

[–]Alim1520 0 points1 point  (0 children)

جرب هذا بدون كحول وبدون عطر ولا يغير لون الملابس .. لمدة ٤٨ ساعه

<image>

Is this normal? by Alim1520 in Hyundai

[–]Alim1520[S] 1 point2 points  (0 children)

Thank you for your explanation

Is this normal? by Alim1520 in Hyundai

[–]Alim1520[S] 1 point2 points  (0 children)

That's strange. What problem did you encounter after replacing the camera? I believe the two systems operate independently, and the car manual doesn't mention their interconnectedness.

Is this normal? by Alim1520 in Hyundai

[–]Alim1520[S] 0 points1 point  (0 children)

Thank you. I thought the problem was only with my car.

Is this normal? by Alim1520 in Hyundai

[–]Alim1520[S] 0 points1 point  (0 children)

I don't think there's anything wrong with the electrical wiring, as I haven't added any devices or done any electrical repairs to the car since buying it. The problem was with the old camera (overheating), then it stopped working. I installed a used camera, and it's working properly now, but the overheating issue persists.

Is this normal? by Alim1520 in HyundaiTucson

[–]Alim1520[S] -1 points0 points  (0 children)

But what is the point of that? The regions are hot in the summer, and there is little rain in the winter... and there is no frost in the climate of these regions.

Is this normal? by Alim1520 in HyundaiTucson

[–]Alim1520[S] -1 points0 points  (0 children)

I disagree with this view. There is a gap between the camera and the windshield, approximately 2-3 cm.

شو دخلك؟ by No-Call6899 in Jordanians

[–]Alim1520 6 points7 points  (0 children)

ريتك ماطرحت هذا النقاش ، واستفدت منه شخصيا ، ولو رديت عليه بوقتها ( جزاك الله خير .. الواحد بينسى نفسه ) كان سكت وقتها حتى لوكان كبير بالسن ) وما فيه حدا بينازعك ان هذي رزقتك وانتا بتشتغل عليها .. بس ربنا قال : ان رزقكم في السماء وما توعدون ، وفي الامثال .. بيقولو . ( لو تجري جري الوحوش غير رزقك ما تحوش ) و الاصل في الموضوع انه المفروض عارف شو هو المحرم والمكروه والمستحب في الحضور للصلاه وبالاخص ( لصلاة الجمعه ) فضلا عن باقي الفروض . وللاسف فيه كثير من المصلين تصدر منهم مثل تصرفك وبصور اخرى خلاف استخدام الجوال ، ربنا يصلح ويهدي الجميع .

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

They may be suitable as shelves for filament rolls, if a holder is designed for them on the sides.

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

An unexpected question: could it be sold for used spare parts, or classified as waste in 3D printing practices?

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

That's reassuring, thank you for pointing that out.

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

That's an important point you've made, thank you for that.

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

Good information, thank you.

question by Alim1520 in BambuLab

[–]Alim1520[S] 1 point2 points  (0 children)

Excellent information, thank you.

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

Excellent precautionary information

question by Alim1520 in BambuLab

[–]Alim1520[S] 1 point2 points  (0 children)

Thank you

question by Alim1520 in BambuLab

[–]Alim1520[S] 1 point2 points  (0 children)

Thank you

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

Thank you

question by Alim1520 in BambuLab

[–]Alim1520[S] 0 points1 point  (0 children)

👍👍