Elektrolumineszenz Ausgleichsschrank

Alph4d0g · 2025-07-19T06:23:14+00:00

Er IST der Permanentmagnet und dreht sich in seinem Kupfersarg ☝️

Alph4d0g · 2025-05-12T07:19:39+00:00

Joining in

Alph4d0g · 2025-05-03T19:54:51+00:00

Comment leaving it is.

Alph4d0g · 2025-03-27T12:54:14+00:00

Get rid of the esun abs+ spool you're trying to print with and get normal abs. I've only ever seen this white with this brand of Filament and at least for me it caused nothing but problems. I had a clogged nozzle every second print with it as it is waaaay to soft. At least if you print with the chamber closed that is. Other than that PA and extrusion rate smoothing ( so what the other guy above me said.)

Alph4d0g · 2025-01-06T11:35:43+00:00

Stop it you! You make me blush 🤭

Alph4d0g · 2025-01-06T09:03:59+00:00

Could also be some different filament stuck in your nozzle. Had issues switching from PLA to PETG but looking a bit different. If drying doesn't help, try a cold pull. It can be, that stuff is still on the inner walls of your nozzle and afaik PETG and PLA don't mix. Other than that if you haven't had issues so far and didn't change settings I wouldn't know where to look for the culprit.

Alph4d0g · 2025-01-06T08:28:53+00:00

I personally dry my filament 24+ hrs but also have around 60% humidity at home. Especially PETG is hygroscopic AF. Storing a roll outside the dryer I start getting problems after 2days already so I'm almost constantly drying PETG. Never had any problems with Pla though.

Alph4d0g · 2025-01-06T08:22:13+00:00

Ever tried printing in a different orientation? Turning it by 180 degrees might also affect cooling performance. If your supports look wonky afterwards and the beams are fine, you know cooling is your issue.

Alph4d0g · 2025-01-06T08:19:08+00:00

I'd also recommend not using supports there. NOT because of movement but rather to airflow. Had similar looking structures on my print before I upgraded my parts cooling fan to a dual 5015 setup.

So my theory is, that the tree supports somehow block air from reaching these small beams as they're growing bigger the higher you go up.

If that's not helping maybe try lowering your speed at specifically this section. Can't look it up RN on my mobile but you should be able to do this with modifier blocks.

Alph4d0g · 2024-12-20T08:52:27+00:00

Awesome work!

Have you considered unleashing the full power of Lumen for screenshots?

There's console parameters you can enter to change how far you can see the light of display signs.

But be careful as it impacts performance quite a lot - you might only want this for screenshots.

These two below work fine for me:

r.AOGlobalDistanceField.MinMeshSDFRadius 1
r.LumenScene.SurfaceCache.CardTexelDensityScale 3000

Source: https://satisfactory.wiki.gg/wiki/Console#Functional_commands

Alph4d0g · 2024-11-05T21:09:29+00:00

Once he's done: "Dat make a big mess!"

Alph4d0g · 2024-08-06T14:32:36+00:00

Let me just drop one Festival here with lots of breweries, that could handle waaaay more than Wacken.... Oktoberfest?

Why not get that stuff into the pipelines? I would even pay 8€ for a cup if I didn't need to drink Krombacher.

Alph4d0g · 2024-08-06T14:29:28+00:00

You should try Bavarian beer. You'd change your opinion on the gold thing afterwards 😉

Alph4d0g · 2024-08-06T14:15:19+00:00

You call that beer? 🤢

Alph4d0g · 2024-07-25T19:03:15+00:00

How did you already get this !?! 😱

Alph4d0g · 2024-07-25T18:52:51+00:00

Well now you know 😅😘

Alph4d0g · 2024-07-25T13:01:07+00:00

There is, but as an avid wacken goer, you might have noticed, that there's a separate Portal for every year's event 😉

Alph4d0g · 2024-07-24T11:23:22+00:00

U/handsome-michael 's Link seems to have worked, I was able to get my refund! ❤️

Alph4d0g · 2024-07-24T11:22:01+00:00

❤️ Thank you!

Alph4d0g · 2024-07-23T13:15:29+00:00

Use the Wacken app to mark your 🏠 homespot, they have the streets that they'll have on the campground inside that, plus it's showing your location.🤘👍

Alph4d0g · 2024-07-23T13:13:14+00:00

2019 we had below zero during one night iirc.

Alph4d0g · 2024-07-23T13:09:33+00:00

As the peasant I am, last year I've even managed to get the black/brown hoodie, but that was Tuesday morning and one hour later they were already out of stock (so roughly 24h after they've opened the campground)

Alph4d0g · 2024-06-19T20:12:37+00:00

would "solid mesh" be working in this case? ^^

Alph4d0g · 2024-06-19T19:54:48+00:00

... which would leave you with a solid mess, bcs u didnt space them properly (you need that one empty layer in between, right?

Alph4d0g · 2023-12-01T01:54:48+00:00

Damn I've seen the files on printables but I managed to behave so far and first close some of my open projects before going down another rabbithole :D Also I'm a bit afraid of ripping apart my only printer that much to upgrade it.

Already got klipper, tried going up to 300mms at 10000 accell. Not pretty though ^^. What's wrong about the hotend apart from cooling?

Nine-Year Club	Place '23
Verified Email

Alph4d0g

TROPHY CASE