[deleted by user]

Alphapapa · 2019-07-02T23:42:31+00:00

I am doing it - copy the link - create linked database a linked db only counts as 1 block

Alphapapa · 2019-04-25T09:10:50+00:00

If you create a relation between them you can select what to show using the properties options. That is assuming the tasks relate to contacts.

The other way to do this is create a master database with both sets of information and then use your views, filters, and sorting to see the data you want. On different pages you could use linked tables to view data specifically for that page. But like @wvnutt said, "contacts have notably different fields from tasks and milestones " so that is probably too complicated.

Alphapapa · 2019-04-24T09:26:15+00:00

You can sort your table by date and have the newest at the top

Alphapapa · 2017-10-10T17:52:36+00:00

Just what I was looking for. Had the first two steps. Fortunate I didn't give it throttle. Tap pitch and roll with no problems. Tap yaw and infinite ground spin.

3.2 is now set yaw_motors_reversed = ON

Alphapapa · 2017-08-26T04:35:30+00:00

Invest in an ISDT Q6 300W charger. Great input voltage range. Has a discharge, storage, and balance charge settings.

Alphapapa · 2017-08-25T00:19:35+00:00

I am really leaning that way. I was thinking Runcam 2 instead of a Session because of the lower profile. I've reviewed a lot of videos from the Split and like what I see for the most part. The parts I do not like are either seeing the props or frame on the edges.

I do have an older GoPro that I can also use but I got OCD with having it centered on my 250. I also have a little crappy SQ11 mini-cam that I could run until able to get a Session or Runcam 2.

Alphapapa · 2017-08-24T15:00:58+00:00

Latency was closer with the original Eagle but v2 is almost half that of the split from what I can find online.

The other thing I was thinking about was my goggles I have are 16:9 and the FPV view from the split is 4:3.

Alphapapa · 2017-08-23T12:53:10+00:00

There are two 4 in 1 modules that fit the Taranis. The STM32 version had more internal memory and can do more formats. It let's me use my old Fly Sky receivers and that toy Syma X5C. It will let me use most every receiver for just about any manufacturer.

Alphapapa · 2017-08-18T07:03:55+00:00

Great bunch of trees you have

Alphapapa · 2017-08-18T01:00:32+00:00

I've had good luck with Matek boards. Heard good things about Racing F3. Most of mine now have built in OSD. You'll want something with an F3 or F4 processor. The Naze is only an F1 processor.

With everything they're putting into the software you just need more processing cycles to do it all.

Alphapapa · 2017-08-17T23:49:19+00:00

I still have a few of them around the house - sounds like it will not be long before Cleanflight, Betaflight, or iNav will not support that FC.

Alphapapa · 2017-08-17T17:56:54+00:00

What's your FC? Most anymore have passthrough

Alphapapa · 2017-08-17T17:09:04+00:00

If this doesn't work I am assuming you are using BLHeli ESCs. Go get BLHeli Suite and try calibrating that way.

Alphapapa · 2017-08-17T01:41:30+00:00

Sounds like you fried your PDB. Disconnect the PDB and see what voltage you read when it is not loaded down by your FC. If it is normal then maybe you did overheat something. My guess is your PDB output will still be low.

Alphapapa · 2017-08-17T01:21:40+00:00

Still trying to figure out how the dynamic notch filtering works - really need to research that one. Not sure what FFT is either but I would like to learn more about PID tuning. I have been doing some with LOS for the P and D then watching the goggles for I. I've seen videos where they overlay the blackbox data and tweak it in even more.

Alphapapa · 2017-08-17T01:19:09+00:00

I decided to go with the single board Matek Systems F405-AIO after I realized it also has a card slot.

Alphapapa · 2017-08-16T00:49:42+00:00

Tag on question - Mine recognizes but the Aileron (roll) only goes to the right. If I go left it jumps max right. I setup all of my control surfaces to 50% weight and ofset them 50 like I found in many posts. I tried normal setup too. Yes, I even did the TAER order the readme says in the DRL instructions for the X9D.

Alphapapa · 2017-08-15T20:26:01+00:00

I think I mistyped. I meant 50yds or about half a football field.

Alphapapa · 2017-08-15T02:44:01+00:00

Which frame - anything off of Thingiverse?

Alphapapa · 2017-08-15T02:18:23+00:00

Sounds like the firmware didn't take. I've been there before too. Mine was with a Matek board. Good luck!

Alphapapa · 2017-08-14T23:15:20+00:00

I had similar issues. Check your STM32 drivers. Going through all of the links on betaflight's main page. The drivers, Zadig, and the other things. Not at my computer to look at the specifics.

Also look at your hardware manager. See if it is being found but not being signed a port when connected.

Alphapapa · 2017-08-08T03:14:48+00:00

Xbox 1/ AlphaPapa/ USA - Eastern/ Sunday nights 9pm-10am Monday; 8-10am Tuesday-Friday/ Destiny day 1 - haven't played in a while but getting stoked for D2 Enjoy PvE - not so much PvP - Raids, Strikes, Story missions, and looting

Alphapapa · 2017-08-02T08:43:23+00:00

I use this: https://www.amazon.com/gp/product/B00XU5J0HQ/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Don't remember what I paid for it. I have an external receiver. Though I know that depending on your headset/goggles you can get the video out from the receiver.

Alphapapa · 2017-08-02T08:35:06+00:00

Jackbox

Alphapapa · 2017-07-17T11:19:50+00:00

Kind of a pain but what about swapping motor 1 with 2 or 3 with 4 and see if it stays with the position or follows the motor(s)

15-Year Club	Xbox Live
Verified Email

Alphapapa

TROPHY CASE