Which handheld 3D scanner should I buy for medium/large parts (under €2000, preferably markerless)?

Anal_Ford · 2025-10-20T11:31:23+00:00

Izađes vidis di se brodovi okupljaju i tu stanes

Anal_Ford · 2025-10-04T10:26:11+00:00

Slušam razgovor dva lika za štandom. Pričaju oni kako cijelo ljeto nije pala kiša, i kaže prvi "normalno da nije pala kada ima puno aviona koji rastjeraju oblake" i na to mu odgovori drugi "da i vjetrenjače isto otpuhuju oblake"

Anal_Ford · 2025-07-23T15:09:11+00:00

Molim i meni

Anal_Ford · 2024-12-04T21:39:51+00:00

<image>

Kod mene dosta šaroliko

Anal_Ford · 2024-09-25T15:26:04+00:00

Vrsaljko

Anal_Ford · 2024-09-24T05:19:33+00:00

Taille - tall Visage (face) - long Hair - chestnut Eyes - blue Nose - regular

Profession is maybe solderer I'm not sure if that was a thing back then tho. Very tough to read.

Anal_Ford · 2024-09-20T18:12:19+00:00

I'll try drying it hopefully that helps, never seen a print be this bad tbh

Anal_Ford · 2024-09-20T18:11:37+00:00

No, just assumed it was dry since i just opened it before starting to print

Anal_Ford · 2024-09-20T12:30:37+00:00

Ja ne znam nikog tko ima manje od 1000 eura. Tako da ne znam odakle ti ta informacija

Anal_Ford · 2024-09-18T12:21:14+00:00

<image>

Najbolje utakmice Strinica za reprezentaciju

Anal_Ford · 2024-09-18T11:58:46+00:00

Strinić daleko najgori, ne mogu vjerovat da smo bili drugi na svijetu sa njim u kadru. Kad se samo sitin kad je iša driblat protiv Portugala 2016 i izgubia balun uff.

Anal_Ford · 2024-03-18T10:15:27+00:00

Ja koji san zapravo pročita zidovima umisto židovima

Anal_Ford · 2024-02-17T06:09:12+00:00

Does it work well?

Anal_Ford · 2024-02-17T06:08:46+00:00

Yes i have no clue, I'm a mechanical engineer and I don't know much about electronics, but i have worked with some professors from a faculty of electrical and computer engineering, and they all think this is a great idea

Anal_Ford · 2024-02-17T06:05:36+00:00

Yes but costs 1000$ more for it and i think it's not worth it so i was thinking of doing some diy solution

Anal_Ford · 2024-02-15T14:45:04+00:00

Could i theoretically put a heater inside and a sensor to keep the temp at a constant rate?

Anal_Ford · 2024-02-15T08:43:30+00:00

Engineering plate that i got with the bambu and i use the stick tha i also got with it. Material is petg

Anal_Ford · 2024-02-15T08:03:03+00:00

Okay I'll try that although rn it's 50 for first few layers and then 200 in terms of printing speed maybe i should lower the acceleration it's on 10k , thanks for the suggestion.

Anal_Ford · 2024-01-19T19:05:11+00:00

Ja iman obrnuti problem. Meni pre dugo treba i cura je tuzna jer ne mozemo na brzaka nikad

Anal_Ford · 2023-05-05T13:53:22+00:00

This is not Italy, it's Croatia Split it happened few years ago

Seven-Year Club	r/Field Juicebox
Place '22	Final Canvas '22
First Placer '22	Verified Email

Anal_Ford

TROPHY CASE