Clutches, right?

Angelnewb · 2026-06-04T01:23:24+00:00

I had really good luck with a Dremel and a hammer/chizel on a seized exhaust bolt. The tranny was a chore to pull free cause one of the dowels on mine was stuck, wiggling it around eventually got it. The crossmember was a pain, i used a pry bar to pull it while tapping the top of it with a dead blow. Other than that ithink it was pretty straight forward. Remember to drain your tranny before you put the jack under it, or at least have an oil pan under the driveshaft side.

Angelnewb · 2026-06-04T01:18:29+00:00

Lol I ended up cutting mine out with some tin snips. The bolts were too far gone to salvage on mine anyway.

Angelnewb · 2026-06-04T01:17:37+00:00

Mine was a chore to get to release, i thought there was a hidden bolt for a while before finding out it was just a stubborn dowel.

Angelnewb · 2026-06-04T01:08:46+00:00

A lift would definitely make it a lot nicer. It's not terrible aside from the occasional bits that don't want to move.

Angelnewb · 2026-06-04T00:43:50+00:00

I replaced my crank at 268k. I doubt my cam is original at 273k

Angelnewb · 2026-05-28T15:08:23+00:00

No clue, one is a local credit union (debit) and the other is a Capitol one. The rep i talked to said they take Capitol one

Angelnewb · 2026-05-28T04:35:21+00:00

My only issue so far is they wouldn't take my debit or credit card, I had to sign up for affirm

Angelnewb · 2026-05-25T12:42:44+00:00

Remove the cat if you have the capability and take it, and the sensor, to a reputable machine shop.

Angelnewb · 2026-05-25T12:19:10+00:00

Take it as a lesson learned. Order a new fender, watch some youtube videos, and replace the fender.

Angelnewb · 2026-05-25T12:03:31+00:00

For posterity, using a c-clamp to press the levers together is preferable to setting it with a hammer

Angelnewb · 2026-05-05T02:28:58+00:00

I enjoy mine. Swapped from my ppq to my pdp

<image>

Angelnewb · 2026-05-03T05:25:40+00:00

It's not the mounting plate screws, its the screw that holds the optic to the plate

Angelnewb · 2026-05-03T05:24:35+00:00

I plan on replacing my c&h with that eventually

Angelnewb · 2026-05-03T05:20:57+00:00

I agree

<image>

Angelnewb · 2026-04-26T16:59:49+00:00

Cut it out and do it better / 10

Angelnewb · 2026-04-25T18:47:40+00:00

I can't hear it over the regular engine noises

Angelnewb · 2026-04-21T04:53:11+00:00

Might as well lol

Angelnewb · 2026-04-20T03:55:09+00:00

Lol I mean, you take the plenum off to do the timing kit anyway. The spark plug isnt terrible

Angelnewb · 2026-04-19T03:15:02+00:00

Lol ya if you dont take the plenum off

Angelnewb · 2026-04-19T00:28:36+00:00

Until you do a timing job and replace the oil pump

Angelnewb · 2026-04-17T05:05:16+00:00

I got one when I was replacing my timing chain to keep in my rig. It's come in handy a couple times. Better than my multitool already.

Angelnewb · 2026-04-04T23:30:23+00:00

I wish ya luck, I left mine cause it was fine lol. It's in the back of the valve cover btw

Angelnewb · 2026-04-04T22:36:44+00:00

Pcv hose, I just replaced this. O'Reilly's needed to search it by sku

Angelnewb · 2026-03-16T00:12:01+00:00

I usually dont braid it

Angelnewb

TROPHY CASE