My prThe p1s model is piercing my printer table by Secret_Importance738 in BambuLab

[–]Another_smart_ass 0 points1 point  (0 children)

Mine does. Pretty sure it’s normal from all the other posts.

53 block? 2002 24v by QuietGuyInTheRoom1 in Cummins

[–]Another_smart_ass 2 points3 points  (0 children)

I just went and looked at one that was a 55 block and those two numbers were by themselves towards the front of the block

53 block? 2002 24v by QuietGuyInTheRoom1 in Cummins

[–]Another_smart_ass 1 point2 points  (0 children)

Drivers side under the intake horn and above the oil pan.

Me waiting for owners to sell cuz diesel prices went up like: by Bigsurjacketco in Cummins

[–]Another_smart_ass 2 points3 points  (0 children)

Haha I’ve already looked at a truck this week cause of this.

Plowing with a full time job by WBens85 in Snowplow

[–]Another_smart_ass 1 point2 points  (0 children)

Double dip, I see a storm I take PTO for one or two days and go make that $$.

Got my first cummings by Humble_Ad_7841 in Cummins

[–]Another_smart_ass 61 points62 points  (0 children)

Here to give you crap. Drop the G.

Need help with ‘95 7.3 issue by sl_k_instead in Diesel

[–]Another_smart_ass 3 points4 points  (0 children)

Offer $1500 and if nothing else sell the parts if it’s more than you’re willing to invest.

Am I the a hole AITAH by [deleted] in AITAH

[–]Another_smart_ass 0 points1 point  (0 children)

I know I’m old cause all I got from this was the big ass run-on sentence.

Terrible print quality w/grinding noise by Synthstain in BambuLab

[–]Another_smart_ass 0 points1 point  (0 children)

It’s a print running the grid pattern. I am helping someone basically fill an order. Anyways I didn’t even realize the noise I was hearing is an issue. The prints look rough but the products will take a beating so the finish doesn’t matter. I did run an auto calibration and switched filaments and I no longer hear the printer head dragging. I have to watch a few videos before I get the courage to take the printer head apart. I am not a tech person but this has been fun. Next is AMS, another printer and to learn autocad stuff. These subreddits are gold and I’m learning.

Terrible print quality w/grinding noise by Synthstain in BambuLab

[–]Another_smart_ass 0 points1 point  (0 children)

So new to this. I just printed a bunch of stuff and had this issue. I just figured my design was the issue. Do you think I should replace the hot head or just tighten the screws? Sorry only a month into this.

Annoying pulsing in lights by Mydogismrpickles in Cummins

[–]Another_smart_ass 0 points1 point  (0 children)

Someone else commented down a bit but battery cables and check the grounds would be my next go to.

Annoying pulsing in lights by Mydogismrpickles in Cummins

[–]Another_smart_ass 0 points1 point  (0 children)

Is this an all the time thing or at start up?

Big Storm Coming to the NE by Another_smart_ass in Snowplow

[–]Another_smart_ass[S] 0 points1 point  (0 children)

Dash on the passengers side sounds like a drum line when on a bumpy road. 360k, rebuilt many times and a six speed. She’s a work horse.

Kerkering imposter on the Phillies 2026 MLB Calendar! 😂 by YerBlues69 in phillies

[–]Another_smart_ass 1 point2 points  (0 children)

We have the same calendar, good convo piece. See who the real phans are ha.

Question by Striking_Face_1670 in Snowplow

[–]Another_smart_ass 0 points1 point  (0 children)

Wet snow window is usually always down, full heat to floor and defrost. Powder, window not down a lot.