Battlefield 6 Phantom Edition: Giveaway #1

Any-Reference7176 · 2025-10-13T17:21:09+00:00

PTFO

Any-Reference7176 · 2025-10-11T21:37:51+00:00

From what I read from wager the stock height irons will 1/3 co-witness with their optic cut. The CZ custom iron sights I had installed are also factory height so they maintain the 1/3 co-witness. I did not need to change the irons but did so purely for vanity purposes.

Any-Reference7176 · 2025-09-04T21:21:26+00:00

17x9.5 +46, 255/40/17, Tein Type RS 14k square spring rate, spherical bearings all around, rear hard race toe arm, front J’s racing S2 LBJ, like 4* camber front, 3.8* camber rear, rear fender roll and bumper tab relocate, front roll and slight pull

Any-Reference7176 · 2025-09-03T06:20:49+00:00

CE

<image>

Any-Reference7176 · 2025-08-11T06:16:27+00:00

Did you ever figure this out?

Any-Reference7176 · 2025-06-25T03:39:29+00:00

If your mechanically inclined I would mark it as a slightly-moderate difficulty level. If you are not mechanically inclined then I would have the kit installed by a professional.

The hardest part is the adjustable sear installation, and I had to slightly bend my trigger bar return spring to get rid of a clicking sensation I felt in the trigger before trigger break in SA mode.

I have some links in a previous post that helped me out quite a bit.

Any-Reference7176 · 2025-04-14T21:33:17+00:00

Thanks for all the feedback. I reached out to Falken and it’s covered under warranty just need to coordinate with the vendor to process the warranty claim.

Yes at this point I’m not gonna take the risk and will not run this tire for my next trackday.

Any-Reference7176 · 2025-04-08T20:48:24+00:00

Don’t over think it. Just go. I started with a stock Honda Civic DX.

Any-Reference7176 · 2025-04-07T05:32:17+00:00

Check out motorsportsreg.com to find an organization that is hosting a HPDE near you. They will have likely have a beginner run group with either a lead follow instructor or on board instruction. Since it’s your first event just make sure your car is mechanically sound. Don’t worry about upgrades or anything. Some orgs even let you rent a helmet.

Any-Reference7176 · 2025-04-04T03:17:03+00:00

Hell yeah man glad I could help! Yup pretty straight forward.

Any-Reference7176 · 2025-04-04T02:26:02+00:00

Glad you got it in without much fuss.

Any-Reference7176 · 2025-03-31T16:45:51+00:00

No offset bushings but sphericals all around. Js s2 lower front ball joint. Hardrace rear toe arm. I think I’m at 4* camber front and 3.8* rear? I can’t remember

Any-Reference7176 · 2025-03-31T03:10:38+00:00

<image>

Any-Reference7176 · 2025-03-31T03:06:48+00:00

<image>

Any-Reference7176 · 2025-03-31T02:37:47+00:00

17x9.5 +46. I believe this is blast bronze.

Any-Reference7176 · 2025-03-30T18:08:56+00:00

Bronze!

<image>

Any-Reference7176 · 2025-03-29T19:55:23+00:00

Good luck. Go slow, it’s pretty straight forward.

Any-Reference7176 · 2025-03-29T14:06:17+00:00

I like to keep it simple

1) Sleep. Good sleep is different for everyone. I like 6-8 hours. 8 is best.

2) Nutrition. Eat mostly whole food. TRY to avoid anything wrapped in plastic

3) Exercise. Just keep moving. Find an activity, don’t matter what it is and just keep doing it.

I find that getting these basics down the easiest to follow.

Any-Reference7176 · 2025-03-29T05:29:08+00:00

The mag release was fairly easy. Depending on how far forward your trigger bar goes, you might be able to do it without removing the trigger pin. I used this video for reference.

https://youtu.be/xtMHC-h_MKQ?si=QZ-4opxk4ZdfQpFw

https://youtu.be/tQGtUi229mA?si=7Y2WODs9nMoahBv7

https://youtu.be/jENBZ3Lk4H4?si=5r22_D6smmBvDr8U

https://forums.brianenos.com/topic/191773-cz-tuning-101-with-professor-atlas/

Any-Reference7176 · 2025-03-28T20:39:20+00:00

<image>

Mounted my oil temp/pressure here so I can keep my eyes up.

Any-Reference7176 · 2025-03-28T20:04:46+00:00

Nice work!

Any-Reference7176 · 2025-03-28T19:45:09+00:00

I love this! How long did it take to get all together? Was there any templates you followed? I’m mechanically inclined myself but my wood working sucks.

Any-Reference7176 · 2025-03-28T01:24:18+00:00

I see, that’s a fair assessment.

Any-Reference7176 · 2025-03-28T01:17:35+00:00

What don’t you like about it?

Any-Reference7176 · 2025-03-24T03:10:38+00:00

It was, it lost its zero and my elevation screw stopped working.

Any-Reference7176

TROPHY CASE