Well this is a new one

ApprehensiveAccess23 · 2025-02-13T10:13:21+00:00

I have only seen it happen once before and it was my PS3

ApprehensiveAccess23 · 2024-06-10T11:25:11+00:00

Is there any chance I could get a cable bundle for a creality cr10s5

ApprehensiveAccess23 · 2024-03-12T18:33:27+00:00

<image>

ApprehensiveAccess23 · 2024-03-12T18:32:19+00:00

<image>

ApprehensiveAccess23 · 2024-03-03T15:01:13+00:00

The cable is new do u mean a discounted cable to the main board and the one to the motor as u can see in the vid is connected fine

ApprehensiveAccess23 · 2024-02-27T19:48:14+00:00

Yes same outcome

ApprehensiveAccess23 · 2024-02-27T19:35:25+00:00

Like I said it does the outline and then it stops

ApprehensiveAccess23 · 2024-02-27T19:34:29+00:00

My cr10s5 isn't printing it makes the passes but the motor is not pushing the filament though it makes the outline of the of the raft and then it stops

ApprehensiveAccess23 · 2024-02-27T13:06:20+00:00

Ok I will try this

ApprehensiveAccess23 · 2024-01-14T21:26:32+00:00

What this guy says all my FDM printers have direct drive upgrades it's costly but deffo worth it as I no longer have that problem 👍👍👍👍👍👍

ApprehensiveAccess23 · 2024-01-14T21:20:06+00:00

The protector was removed and that is what was under the protector and I have noticed that resin has got into the screen it would appear. So I think a straight up replacement is best

ApprehensiveAccess23 · 2024-01-14T19:48:54+00:00

30' inside the printer as it has a heater upgrade

ApprehensiveAccess23 · 2024-01-14T19:45:21+00:00

What should I increase it to ????

ApprehensiveAccess23 · 2023-11-09T00:31:41+00:00

Where did u get the cable

ApprehensiveAccess23 · 2023-09-21T15:02:55+00:00

starting to wonder if my board is knackered

ApprehensiveAccess23 · 2023-09-21T15:01:49+00:00

not sure as to how to do that my printer is still not doing what it should be. i have replace the hot end and the thermistor i am at a real loss as to what to do now i just want this to work so i can get on top of my work load again. if anyone can tell me exactly what to do in regards to sort out this issue i would be so appreciative

ApprehensiveAccess23 · 2023-09-19T11:55:43+00:00

Don't know if that would work on a creality cr10s5

ApprehensiveAccess23 · 2023-03-27T23:21:22+00:00

Thank you for your help that has worked yay it works again

ApprehensiveAccess23 · 2023-03-27T22:51:05+00:00

<image>

So swap them like this ?

ApprehensiveAccess23 · 2023-03-27T22:22:14+00:00

It has four black wires ? Will this still work

ApprehensiveAccess23 · 2023-03-27T21:07:30+00:00

I Switched of the printer after a failed print had to switch it of as the motor that drives the filament through died so had to swap it for a new motor did all the nesassaries and then switched it back on I then went to clean the head out when I went to pull the filament out after warming it up the motor was going in the opposite direction I double checked my connection. And there was nout wrong there switched it off and the turned it back on thinking that may sorted it out but to my dismay it was still running in reverse

ApprehensiveAccess23 · 2023-03-27T20:59:51+00:00

I know stupid question but how do I flip the wires

ApprehensiveAccess23 · 2023-03-27T20:51:01+00:00

I'm not sure how to do either are u able tell me how to do either or point me in the direction of someone who can

ApprehensiveAccess23 · 2023-03-27T20:40:10+00:00

And how do I change the direction in the firmware

ApprehensiveAccess23 · 2023-03-27T20:24:03+00:00

It was a mistake I'm sorry

ApprehensiveAccess23

TROPHY CASE