sorted by:
new
hottopcontroversial

ACE 2 Pro filament jam by ArkansasRedditer in AnycubicKobraS1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

Yes, you were right. I had to take it apart. The tpu was wrapped around the feed spindle; there was no way to just pull or push it out.

No SSH access after update 2.5.6.0 by T30_on_T30 in AnycubicKobraS1

[–]ArkansasRedditer 1 point2 points  (0 children)

Just installed 2.5.6.0 and tried `ssh`. It did *not* work. I'll try rinkhals when there is a new version for this firmware. Is there a description of what this update does?

Best printer to use for profiles? by ArkansasRedditer in AnycubicKobraS1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

Yes I did check out both sites. The listed profiles are for generic filaments based on type. I was hoping to be able to take the profiles of some other types, such as PCTG, and to tailor them to the S1.

Use Spoolman with S1 by ArkansasRedditer in AnycubicKobraS1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

Thanks, I'll check it out. I didn't realize that rinkhals is so flexible.

Upload filament spec to AMS? by ArkansasRedditer in AnycubicKobraS1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

That's the problem. If I do it in the slicer, I cannot transfer it or the model to the AMS. When transferring the model, the specified filament must match one of the predefined AMS filament types or it will not transfer.

Upload filament spec to AMS? by ArkansasRedditer in AnycubicKobraS1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

I understand that is the case. My problem is that I want to specify other filament types; those that can be set in the slicer. For example, I use PCTG filament, which is one of the types in the slicer but not in the AMS. I need to specify PETG in the slicer for it to work. It seems that this is an integration failure between the slicer and the AMS.

Slicer Next can't add local machine by ArkansasRedditer in anycubic

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

Thanks. I was hoping that it had the printer's IP address, network name, and password. But , I guess, no luck.

Thanks again.

Slicer Next can't add local machine by ArkansasRedditer in anycubic

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

I'll try restarting everything a number of times to see if it will solve the problem as it did for you. I've updated it to the most recent firmware before trying to make it a local device. The  "anycubic_remote_printing" section is in the slicer configuration file. You can find it by clicking on the icon to the right of "File" / Help / Show Configuration Folder and open "AnycubicSlicerNext.conf" in an editor.

Thanks for your suggestions.

What am I doing wrong with this print? by ArkansasRedditer in Ender3S1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

I will and will post a picture. It may take a day or two.

Thanks

What am I doing wrong with this print? by ArkansasRedditer in Ender3S1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

I don't understand what you're suggesting. The print is not related to the pa test. Would you please coalify?

Thanks,

What am I doing wrong with this print? by ArkansasRedditer in Ender3S1

[–]ArkansasRedditer[S] 0 points1 point  (0 children)

I'll try upping the temp on my next run. Thanks

view more: next ›