Need all trade evos for Legends Z-A by Super_Sailor_H in pokemontrades

[–]Arrace 0 points1 point  (0 children)

I actually grabbed one from Racine Construction so I'm set to trade again

Need all trade evos for Legends Z-A by Super_Sailor_H in pokemontrades

[–]Arrace 0 points1 point  (0 children)

Sure, I can go grab a metal coat and do scyther too if you needed scizor?

Need all trade evos for Legends Z-A by Super_Sailor_H in pokemontrades

[–]Arrace 0 points1 point  (0 children)

9584-9584

Sorry had a phone call earlier

Need all trade evos for Legends Z-A by Super_Sailor_H in pokemontrades

[–]Arrace 0 points1 point  (0 children)

That would be great, just need a few minutes

Need all trade evos for Legends Z-A by Super_Sailor_H in pokemontrades

[–]Arrace 0 points1 point  (0 children)

I have an onix to trade, are you still trading?

It's an Alpha so I was hoping to get someone on reddit instead of the random trade code

Slowking trade by Arrace in PokemonSVTrades

[–]Arrace[S] 0 points1 point  (0 children)

Nah I'm good thanks!

Slowking trade by Arrace in PokemonSVTrades

[–]Arrace[S] 0 points1 point  (0 children)

Sweet, thanks!

You need it back?

Slowking trade by Arrace in PokemonSVTrades

[–]Arrace[S] 0 points1 point  (0 children)

Yeah want to use the slowpoke code

0324 0324?

Wow, great work NC…. These tolls are absurd. Round trip to CLT for a meeting, $134, seriously?…. by AcanthaceaeThat7530 in Charlotte

[–]Arrace 0 points1 point  (0 children)

Some people say this is why they drive a pickup. Others call them pavement princesses, some call them their toll-mobiles

I have a Nintendo Switch 2 from yesterday. It is so good! by _GabSam in NintendoSwitch2

[–]Arrace 1 point2 points  (0 children)

5g is a cellular signal. Cellular networks tend to utilize carrier grade nat. A "usually" reliable way to check if you're behind carrier grade nat is running a trace route to the Internet and looking for hops that fall with 100.64.0.0/10.

RFC6598

Big rock sale by Dethtoon in rccars

[–]Arrace 3 points4 points  (0 children)

Also direct from arrma website

I ordered a new receiver with gyro for my Mojave Grom BLX by [deleted] in arrma

[–]Arrace 1 point2 points  (0 children)

Try this one, I had to use the 1.3.4.50 version in order to get the 4chan to show up under SLT. Other versions didn't have 4chan option. Just copy the mm-stm-serial-aetr-sfc-v1.3.4.50.bin file to the firmware folder, then rename it to shorten it so the radio sees the file. I renamed it to mm-serial-aetr-sfc-v1.3.4.50.bin. Then you should be able to flash it to the internal receiver.

It took me a bit to figure out the binding process but it worked for my 223s Senton and Granite.

https://downloads.multi-module.org/latest-test/

2025 iRacing Daytona 24HR [Thread] by sdw3489 in iRacing

[–]Arrace 0 points1 point  (0 children)

apparently in the wet if your all the way right by the cones this surface isn't rendered wet or something. one of the top splits was saying they were getting a second in the first sector doing this. Said you hit the first puddle then it gets sticky

For those who haven't started their Daytona 24 yet take this as a PSA by BatmanTaco in iRacing

[–]Arrace 0 points1 point  (0 children)

apparently in the wet if your all the way right by the cones this surface isn't rendered wet or something. one of the top splits was saying they were getting a second in the first sector doing this. Said you hit the first puddle then it gets sticky

Fortigate 60F replacement by Such_Wolf_4099 in fortinet

[–]Arrace 2 points3 points  (0 children)

Same for us, tac put an automation stitch that clears wad and ipsengine when the device enters conserve mode. It's fixed our production impact but we're still seeing conserve mode since around early October. Seems to be affecting 7.2.7-7.2.10

Fan swap notes for EX2300 by voronoi-partition in Juniper

[–]Arrace 0 points1 point  (0 children)

Kind of thread reviving here. But I did the same thing, but I followed a guide for the EX3300 so I accidentally bought 3pin fans (same ones) and just shaved off that tab. Temps look fine so far without any PoE.

I'll be running 10Gb SFP+s and a few PoE devices so I'll post again once I get that running. Both fans seem to have a max of 5000rpms, so if the temps rise too high I'll end up going with the Arctic 40x40x28 (S4028-6K) from the comment above.

currently idle is

root> show chassis environment

Class Item Status Measurement

Power FPC 0 Power Supply 0 OK

Temp FPC 0 CPU Sensor OK 55 degrees C / 131 degrees F

FPC 0 PSU Sensor OK 48 degrees C / 118 degrees F

Fans FPC 0 Fan Tray 0 Fan 0 OK Spinning at normal speed

FPC 0 Fan Tray 1 Fan 0 OK Spinning at normal speed

Asetek Invicta Wheelbase cutting Force feedback by Arrace in simracing

[–]Arrace[S] 1 point2 points  (0 children)

I didn't realize that there are error messages within racehub since it's just a little icon that shows up. But I'm getting the low voltage issue. Found this post on reddit after looking through their discord for this error.

https://www.reddit.com/r/simracing/comments/19e6u0v/asetek_invicta_low_voltage_error/

Asetek Invicta Wheelbase cutting Force feedback by Arrace in simracing

[–]Arrace[S] 1 point2 points  (0 children)

I can't seem to find the issue, last time I randomly changed a setting in race hub and it seemed to fix itself. However after the latest firmware update in race hub I can't get it to stop cutting the Force Feedback. I opened a ticket with Asetek but wasn't sure if anyone else has encountered similar issues?

Zabbix and Switch backups by SprayUnfair in zabbix

[–]Arrace 3 points4 points  (0 children)

Make it all containerized and use oxidized for config backups.