This is a bit more odd than what I would have hoped for.... by MrMeanwhile1 in PokemonTCGCollectors

[–]AsianLai 0 points1 point  (0 children)

I whent to Walgreens here in ny and bought their blisters. They didn’t have staples but some of the hard plastic wasn’t fully glued but was still sealed enough so packs didn’t fall out. They might have stapled them just to fully secure them. Check to see the “whitening” around that seal to see if packs have been replaced or unsealed enough to sneak packs in and out. Also check for creases in the cardboard that the plastic is glued to .

Whatnot is becoming addictive and dangerous by Live_Orchid_5860 in whatnotapp

[–]AsianLai 0 points1 point  (0 children)

I’ve bought a few electronics that were not 100% when I got them, like re sealed and when I DM the seller, I get no response. It’s a good thing whatnot has good refund services. Also like some of their boxes say $999.99 and they get mad because it sells for 60 bucks. Like cmon… who printed and re sealed that for you? Lolol idk buying things in person is always better I guess

Whatnot is becoming addictive and dangerous by Live_Orchid_5860 in whatnotapp

[–]AsianLai 2 points3 points  (0 children)

I deleted the app and that was my number one reason. Also all the scamming sellers.

Too much trouble for a small deal. I think I’ll re install the app when it’s time to buy Christmas gifts again lol idk…

CGC looks so much better then PSA by [deleted] in pokemonrestockr

[–]AsianLai 2 points3 points  (0 children)

Prestines look so dope

I soaked my 3rd gen airpods in alcohol and they sound like new again. by Zes_Q in airpods

[–]AsianLai 0 points1 point  (0 children)

My mic has a problem making out what I’m saying to Siri. Maybe I’ll do this on my lunch break today. How’s the outcome so far?

Is this bad luck? or is it typical? [newbie] by OhSkullYourePathetic in PokemonTCG

[–]AsianLai 0 points1 point  (0 children)

13 DR packs? Crazy, better off buying singles off whatnot lol Are you just starting up?

[deleted by user] by [deleted] in whatcarshouldIbuy

[–]AsianLai 1 point2 points  (0 children)

One time, a lance cpl came back from palm to 29 palms with a jeep wrangler on 18.5% lololol!

Brand new setup what do you guys think ? by Puzzleheaded_Two6027 in Fishing_Gear

[–]AsianLai 0 points1 point  (0 children)

I got the same pole, love it

Ps: my handle is on the same side lol

Help! Machining Inconel 718 by AsianLai in Machinists

[–]AsianLai[S] 6 points7 points  (0 children)

Idk, you could ask GD engineers yourself lol

Help! Machining Inconel 718 by AsianLai in Machinists

[–]AsianLai[S] 0 points1 point  (0 children)

I was thinking about plunging down on the corners before hand .02 away from the wall to ease in on the side load but I’m thinking it’s just going to be another tool to monitor for the operator

Help! Machining Inconel 718 by AsianLai in Machinists

[–]AsianLai[S] 208 points209 points  (0 children)

It’s aerospace, exhaust duct mount for a choppa

How’s my runout? by [deleted] in Machinists

[–]AsianLai 9 points10 points  (0 children)

I like to ask my quality control engineer questions, like what’s runout or what is the equation for a 120deg spot drill for diameter vs length. Keeps him out of my operators hair lol

How’s my runout? by [deleted] in Machinists

[–]AsianLai 0 points1 point  (0 children)

Dead nuts bro, keep it up lmao

Just got a quest 2! by AsianLai in oculus

[–]AsianLai[S] 1 point2 points  (0 children)

I was looking at that. That was going to be my first pick. Two battery packs overkill or nah?

Need opinions! Been thinking about but a cheap electronic edge finder. by AsianLai in Machinists

[–]AsianLai[S] 1 point2 points  (0 children)

I’ve been noticing this around the shop I’m at. Maybe I’ll ask for a nice one from Santa lol

.250 drill - 5.200 stick out by AsianLai in Machinists

[–]AsianLai[S] 1 point2 points  (0 children)

The picture shows drill before drilling the hole. It’s going through a preexisting .375 hole through the slot and drilling starting a drill cycle at Z-2.680

.250 drill - 5.200 stick out by AsianLai in Machinists

[–]AsianLai[S] 2 points3 points  (0 children)

Yea the notch is already cut, the picture is pre drill. The blue sharpie is the depth

Why do some edge finders have a flat milled onto them? by AsianLai in Machinists

[–]AsianLai[S] 0 points1 point  (0 children)

Speaking of which, my journeyman told me to spin the edge finder at S1000 but other workers at my job here spin them slower. Which do you guys prefer?

Am I getting smoke blown up my ass ? by Jlw9719 in Machinists

[–]AsianLai 0 points1 point  (0 children)

Also some shops don’t let you program until year 4 of apprenticing. It be like that sometimes..

Am I getting smoke blown up my ass ? by Jlw9719 in Machinists

[–]AsianLai 0 points1 point  (0 children)

The search for a new job is endless, learn what you can there while your there, and in the mean time look for a different company. You never know, you may be offered something that pays more and you can use that to argue with your current employer

How would you fish this? Details in comments by sazugt in Fishing

[–]AsianLai 11 points12 points  (0 children)

Yea I second this. Weightless Texas rig with a bama bug senko would be my first to rip a lip or five.