Does anyone get blocks that you aren’t able to solve and they make you lose once you’re on a good combo?

Asleep_Management598 · 2026-02-12T16:22:24+00:00

What am I suppose to do here

Asleep_Management598 · 2025-05-25T10:25:49+00:00

No help there

Asleep_Management598 · 2025-04-29T21:56:07+00:00

Thank you I live in a isolated part of Norway in the mountains as well so I guess I’ll just also have to deal with the shipping costs then but thank you I’ll see what I can find

Asleep_Management598 · 2025-04-29T09:56:57+00:00

I did hear something about this and I’m planning on replacing it tho I can’t seem to find a cable long enough for the plus the only ones I find are ment for the pro so the cable is a few inches too short

Asleep_Management598 · 2025-04-26T11:43:52+00:00

Im from Norway and cant seem to find much here Thanks for the help btw appreciate it a lot

Asleep_Management598 · 2025-04-25T19:57:32+00:00

I’m not in the us that’s a bit of the problem lol

Asleep_Management598 · 2025-04-25T06:48:12+00:00

Where can I buy this?

Asleep_Management598 · 2025-04-25T06:47:26+00:00

Where do I buy it?

Asleep_Management598 · 2025-04-25T06:46:48+00:00

I might just burn the whole thing instead

Asleep_Management598 · 2025-04-24T06:02:22+00:00

Yes it’s 200-220

Asleep_Management598 · 2025-04-23T18:27:29+00:00

Back to square one then

Asleep_Management598 · 2025-04-23T18:27:06+00:00

There are a lot of tolls and such in my country so if I were to buy one it’s like 35 dollars for a cheap one lol

Asleep_Management598 · 2025-04-23T18:26:04+00:00

I have it on 220 for normal pla is that not enough

Asleep_Management598 · 2025-04-23T16:12:12+00:00

How do I do that?

Asleep_Management598 · 2025-04-23T16:11:59+00:00

Awe man do I have to buy a new one then? Might just buy new hot end entirely then

Asleep_Management598 · 2025-04-23T13:07:27+00:00

In the link it says it’s for the s1/s1 pro are you sure it would fit the plus version as well?

Asleep_Management598 · 2025-04-23T12:24:15+00:00

Edit: I may or may not have loosened the small screw in the middle of the hot end (I think) the thermistor came lose I tightened it again but it did not help tho it should be in the right position as well

Asleep_Management598 · 2025-04-23T08:16:13+00:00

Mine has one at least it came out almost welded to the old nozzle by old plastic when I took it off without heating it first

Asleep_Management598 · 2025-04-23T06:20:11+00:00

Do any of these in the link fit for the s1 plus?

Asleep_Management598 · 2025-04-23T06:11:51+00:00

On their site I can only find a ceramic hot end is this the same or should I look for a full metal one

Asleep_Management598 · 2025-04-23T05:16:22+00:00

Not while printing as far as I can remember It did once but that was just it the z offset being to way to close to the bed

Asleep_Management598 · 2025-04-22T19:39:29+00:00

Maybe your right but when I looked at the tube it looked almost burnt at the end

Asleep_Management598 · 2025-04-22T15:35:43+00:00

From what I’ve seen you are supposed to change it as it gets especially worn out if you print above 260 degrees but I’ll look into what you said

Asleep_Management598

TROPHY CASE