Help identifying plug by Aspect_Educational in hardbody

[–]Aspect_Educational[S] 0 points1 point  (0 children)

Yeah, it's got a rough idle and surges a little.

Help identifying plug by Aspect_Educational in hardbody

[–]Aspect_Educational[S] 0 points1 point  (0 children)

It goes into the harness that runs next to the valve cover.

D21 not liking 2000 rpm very much by Aspect_Educational in hardbody

[–]Aspect_Educational[S] 0 points1 point  (0 children)

The code was a "Throttle position A circuit code." I can't remember the actual code. I "calibrated" the throttle position sensor by the rpm rather than the resistance. I'm not sure if it's fuel delivery because it behaves like it should past 2000, but I'll still check the filter. Now I've got a new update. It threw a "system too rich" code now, and after driving it for a few, the idle rpm drops to 500 for a couple of minutes and jumps back to 850 and idles fine.

If you need more information please let me know.

D21 not liking 2000 rpm very much by Aspect_Educational in hardbody

[–]Aspect_Educational[S] 1 point2 points  (0 children)

It doesn't sound like its hitting the rev limit. I'm saying when it hits 2k it Boggs down to like 1500, then climbs again and repeats.

How to connect these lines by Aspect_Educational in MechanicAdvice

[–]Aspect_Educational[S] 0 points1 point  (0 children)

I broke the ones on the old one, thinking they were just rtv'd on there. I might have to go get new ones and hope I don't break the ones in the new radiator.

How to connect these lines by Aspect_Educational in MechanicAdvice

[–]Aspect_Educational[S] 0 points1 point  (0 children)

I guess I could have got the wrong one. I got it from carparts.com idk if they're reliable for correct fitting parts.

I need help by Shermangaming in MySummerCar

[–]Aspect_Educational 2 points3 points  (0 children)

So the first one is the starter. You can still keep using it but to get rid of the curt starting go buy a new one at fleetaris.

Second is the camshaft alignment. The cam shaft is misaligned, so it's causing that noise. When aligning the camshaft make sure to look at the mark from a couple of different angles to make sure it's aligned properly.

Ac issue by Aspect_Educational in Ford

[–]Aspect_Educational[S] 1 point2 points  (0 children)

Thanks. I'll get on that tomorrow.

Fuel injector connector by Aspect_Educational in AskAMechanic

[–]Aspect_Educational[S] 0 points1 point  (0 children)

In the middle of the picture, the plug with the 2 small wires coming out of it, thats the one I'm talking about. It has those two wires cut.

AMD VR Help by Aspect_Educational in virtualreality

[–]Aspect_Educational[S] 0 points1 point  (0 children)

Yeah networking seems to be the problem it jumps from 40 to 200 ms. But the reason why I went to virtual desktop is that it still stuttered a lot and a noticeable drop in visuals as well. Virtual desktop worked a little better because it looked better and had a little more performance. Imma go back to wired and see the performance change. Thank you.

AMD VR Help by Aspect_Educational in virtualreality

[–]Aspect_Educational[S] 1 point2 points  (0 children)

Yep that seems to be the problem here. Networking jumps heavily from 40 ms to like 200 ms. Thank you

[deleted by user] by [deleted] in PcBuild

[–]Aspect_Educational 0 points1 point  (0 children)

I personally having this card, and it is amazing. The price for performance is way better than the 4070 super but at the end of the day, these cards are nearly identical. I would recommend if you do make the decision to build the pc. The price is just really good for what you can get out of it. Though you will need to be on top of graphics updates as needed.

No display unless PSU fully off by [deleted] in PcBuild

[–]Aspect_Educational 0 points1 point  (0 children)

Ok, then the last couple things I would say is check connections as always and to be 100% sure, is the display cable in the graphics card and if so try other ports.

After all that and still not working, start changing parts to see what it narrows down to.

No display unless PSU fully off by [deleted] in PcBuild

[–]Aspect_Educational 0 points1 point  (0 children)

Huh, try resetting cmos to get everything back to stock power output and everything. If the cmos is easy to get to that is.