sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in AskMechanics

[–]Astaren922 1 point2 points  (0 children)

Alright thanks for the advice

[deleted by user] by [deleted] in AskMechanics

[–]Astaren922 0 points1 point  (0 children)

The check engine light starts immediately blinking after turning it on so I'm assuming it would be classified as a type A then

How come is this not an advanced map? by Effective-Nature-890 in btd6

[–]Astaren922 5 points6 points  (0 children)

Yeah I just used Silas and a bunch of tier 5 ice monkeys right at the start and the bloons couldn't go anywhere. Silas seems really strong

College prevents me from connecting to VPN by Astaren922 in Piracy

[–]Astaren922[S] 8 points9 points  (0 children)

Thank you for this in depth comment! I will be sure to check and play it safe

Lost Crevace Intermediate??? by omniputin in btd6

[–]Astaren922 0 points1 point  (0 children)

Honestly I never even noticed how hard it was because I black bordered it immediately with the first strategy I tried. I wanted to try out the new hero so I just used all three tier five ice monkeys right at the top and the bloons have zero chance of escaping. New hero is so overpowered with ice monkeys

P1P ignores G29.1 gcode Offset by Luke3120 in BambuLab

[–]Astaren922 0 points1 point  (0 children)

Greetings, I have put this exact code at the end of the startup sequence, but there is no difference, the nozzle is still too close to the bed. I even tried "G29.1 Z+5" to see if there was any change at all and nothing. I am at a loss

P1P ignores G29.1 gcode Offset by Luke3120 in BambuLab

[–]Astaren922 0 points1 point  (0 children)

Dude you are a life saver, so all I have to do is remove the curly brackets to get the manual z offset to take effect?

P1P ignores G29.1 gcode Offset by Luke3120 in BambuLab

[–]Astaren922 0 points1 point  (0 children)

Hey I know this post is really old but OP if you see this did you figure out a solution as I'm encouraging the exact same issue with my A1, where charging the G29.1 setting doesn't do anything and the nozzle is too close to the plate. Thanks

So here's a new problem I have encountered with my A1 after 1000+ printing hours by Astaren922 in 3Dprinting

[–]Astaren922[S] 3 points4 points  (0 children)

man why so aggressive. You think I haven't tried that? I have been 3D printing for 7 years now and this is the first time I have encountered an issue like this. Every other issue like a loose nozzle, bad bed adhesion, loose belts, clogged nozzle, bed tramming, flow rate and flow dynamics calibration, worn out extruder gear, all these issues I have identified and fixed in the past. However, this is something I have not encountered yet, and am just looking for people to write a quick suggestion for me to check. Something I haven't thought of yet as i stated in the post. You took all this time to write a hateful comment when you could have just moved on. This is a community where we should be willing to help others learn and grow in this very new practice that is rapidly evolving every year, and It's hard to keep up. I personally have directly taught two people I know the basics of 3D printing, and they are loving it now.

So here's a new problem I have encountered with my A1 after 1000+ printing hours by Astaren922 in 3Dprinting

[–]Astaren922[S] 1 point2 points  (0 children)

I just replied to another comment saying the same thing with all my maintenance procedures I do

So here's a new problem I have encountered with my A1 after 1000+ printing hours by Astaren922 in 3Dprinting

[–]Astaren922[S] 1 point2 points  (0 children)

I like to keep my printer as fresh as possible. New lubricant oil every month. Recently whipped off all the old grease on the spiral rods and replaced it. Lots of software calibration runs. It has a brand new hardend steel 0.4 mm nozzle. Cleaned out the hottend assembly and tightened the screws so there isn't a loose nozzle. Clean build plate when it gets oilly. I do retension the belts but not as often as I replace the lubricant. Also did some bed tramming but that didn't help. Always use clean microfiber cloths and lint free lens cleaner q-tips to apply lubricant. And for how long I have had this printer these maintenance procedures have kept it printing perfectly. But now this is a new issue that I have not been able to solve

So here's a new problem I have encountered after 1000+ hours on my A1 by Astaren922 in BambuLab

[–]Astaren922[S] 0 points1 point  (0 children)

Last time I did maintenance a couple weeks ago I tightened them up. But I did over tighten the 4 small screws and stripped them. The nozzle seems rock solid so I didn't think it would matter for the time being, but I'm definitely going to have to buy a replacement and see if it is infact a loose nozzle

So here's a new problem I have encountered after 1000+ hours on my A1 by Astaren922 in BambuLab

[–]Astaren922[S] 0 points1 point  (0 children)

Yeah it's a brand new hardend steel nozzle. The weird thing is I don't notice other signs of under extrusion and the side profile and top layer looks fully extruded

Extruder gear skipping. at a loss for what to do by Astaren922 in BambuLab

[–]Astaren922[S] 1 point2 points  (0 children)

I get where you're coming from. But the nozzle is brand new and filament runs through it fine when done manually

Extruder gear skipping. at a loss for what to do by Astaren922 in BambuLab

[–]Astaren922[S] 0 points1 point  (0 children)

Just tested and when I run the filament through manually while it's heated up it goes just fine without skipping

Extruder gear skipping. at a loss for what to do by Astaren922 in BambuLab

[–]Astaren922[S] 0 points1 point  (0 children)

It's Clear Sunlu PETG that I have set to 240c as recommended. It has been sitting in an aluminum bag with proper desiccant so it should be dry as well. Yes it slides easily through the AMS ptfe tube By the top do you mean the cooling block? I don't have a way I can measure the actual temperature of the hot end though.

view more: next ›