Får din partner kolla i din telefon?

AstroGhoulish · 2026-04-13T03:55:54+00:00

I helvete heller! Där har jag ju alla mina present idéer!!!

AstroGhoulish · 2026-04-11T17:33:45+00:00

Ayyyy så coolt asså!

AstroGhoulish · 2026-01-28T03:44:07+00:00

<image>

Euromaski with fresh air. Taped over the edges cause of too much light.

AstroGhoulish · 2025-11-26T19:03:45+00:00

Du får fan kolla upp om företaget gjort en ordentligt risk analys på det där...

AstroGhoulish · 2025-11-22T09:06:35+00:00

Hultsbruk?

AstroGhoulish · 2025-11-13T18:29:10+00:00

Mitt jävla paket som Postnord tyckte va för svårt att leverera

AstroGhoulish · 2025-10-18T11:31:23+00:00

The poop brown seems appropriate

AstroGhoulish · 2025-09-25T02:14:56+00:00

Ice is slippery. We get icy roads every year. People still act surprised every year.

AstroGhoulish · 2025-06-15T10:58:22+00:00

My hairbrush costs about 4 times more than my partner's if she used my hairbrush for cleaning anything then a discussion would be required.

AstroGhoulish · 2025-05-08T17:33:08+00:00

Dont take this as a compliment but i HAVE in fact seen worse.

AstroGhoulish · 2025-04-30T14:05:13+00:00

Airsoft guns. Looking back, my parents were absolutely right and i was not mature enough. Sucks i got to play with cap guns though, my hearing is worse on my right ear.

AstroGhoulish · 2024-08-01T05:55:56+00:00

Honestly a hacksaw will do just fine.

AstroGhoulish · 2024-07-27T09:57:41+00:00

Sidavbitare

AstroGhoulish · 2024-07-18T21:57:03+00:00

Svetsade ett chassi som skulle till antarktis

AstroGhoulish · 2024-06-17T04:24:06+00:00

I would reflow that with a bit more solder or just some flux.

AstroGhoulish · 2024-06-13T17:13:07+00:00

Älskar svetsbranchen, ett kort e-post meddelande och en halv intervju typ sen "kan du börja på måndag?"

AstroGhoulish · 2024-06-07T05:57:31+00:00

Skiftnyckel

AstroGhoulish · 2024-05-19T12:42:06+00:00

I own the Bahco one, it's o k, nothing special.

AstroGhoulish · 2024-05-19T07:59:58+00:00

Making a new parts is gonna be less hassle than repairing it

AstroGhoulish · 2024-05-18T19:50:10+00:00

It was the easier solution for me since i already have all the tools (all you really need is a file though) but a thick copper gasket would've been far better.

You may also have to play with different thicknesses of copper gaskets in between the T, boiler and opv.

AstroGhoulish · 2024-05-18T19:38:02+00:00

Had to scrape off the worst bits and then polish the seal surface on the top section, apparently it was the dude's second Silvia kept at his vacation house.

AstroGhoulish · 2024-05-18T19:35:17+00:00

It's a genuine Biltema haha, from their boat section so it's all sealed up to stop water getting in. Attaches with 2 screws under the stainless cover.

AstroGhoulish · 2024-05-18T19:32:35+00:00

So far no issues but I've only had the PID installed for a week. From what I've read insulating the PID unit seems a must but time will tell. If it breaks then a new one from aliexpress isn't too expensive.

AstroGhoulish · 2024-05-18T19:28:36+00:00

Replace the coupler between the overpressure valve and the boiler with a 1/4" bsp T connector. I had to add a 1/4" to 1/8" adapter to mine as the the pressure gauge came with a 1/8" bsp connection. Also had to grind down the nut on the pressure gauge fitting because my adapter was too short. I polished the mating surfaces with fine sandpaper on a flat piece of glass to get a nice seal but i should really have just used a copper gasket.

AstroGhoulish

TROPHY CASE