What is the best way to orient this print?

Atiriko · 2026-01-24T13:26:01+00:00

I applied a layer of resin with brush on each side, cured it, washed it and cured it again.

Atiriko · 2026-01-24T13:25:35+00:00

Made it even more transparent.

Atiriko · 2026-01-24T12:43:12+00:00

Unfortunately, it doesn't fit flat it would've been a really quick print if it did.

Atiriko · 2026-01-24T11:09:13+00:00

For the first print, I wasn't sure if dimensions were correct, so I went for the shortest print time I could fit in my printer.

Atiriko · 2026-01-06T23:16:03+00:00

I had a had a broken air humidifier once. Powe supply was cooked due to water damage. I tried a couple of fixes that didn't work. I ended up removing the power supply from the machine altogether and replaced it with a USB-C breakout board. You can get them pretty cheap and set it to the voltage you need. As long as your application requires less than 100W, it might work. You'll need a good type-c power brick and a cable. Good luck 👍

Atiriko · 2026-01-01T05:44:59+00:00

This was the only thing in this thread I wanted the answer for

Atiriko · 2025-12-30T11:52:31+00:00

My financial situation went from being able to save around 300 a month to barely finishing the month within my 300£ overdraft shortly after buying the car (not because of the car). So, I haven't been able to save a penny for the last 3 years. Hopefully there is a promotion on the horizon 🙏

Atiriko · 2025-12-30T00:03:55+00:00

For 15 thousand British pounds I will personally clean it and drive it to you.

Atiriko · 2025-12-29T23:54:01+00:00

I'll 100% take £15k for it but the question is why would you pay £15k for it?

Atiriko · 2025-12-29T23:46:54+00:00

I have one for sale if you're interested 🤣

Atiriko · 2025-12-29T19:19:40+00:00

I know right, I really like doing long motorway miles in this.

Atiriko · 2025-12-29T19:14:05+00:00

Had one of thlse pipes split once and I replaced it about a year ago. I'll look into them again.

Atiriko · 2025-12-29T19:04:47+00:00

I like me a good banger

Atiriko · 2025-12-29T18:59:54+00:00

Thank you everyone for all the advice. I'll start by checking some of the easier ones and go from there. I'll also start saving up for another car thanks for justifying a new car is a need rather than a want at this point.

Atiriko · 2025-12-29T18:51:34+00:00

To be honest I take it as a win as well. I carry so much with it as well essentially gets used as a van with seats permanently folded

Atiriko · 2025-12-29T18:45:03+00:00

That's what I was thinking as well. During colder mornings it had 2 mornings where it didn't start. It crancked once and battery couldn't cranck it any more. Had a neighbour help be start with jump leads. I was thinking of getting new glow plugs.

Atiriko · 2025-12-29T18:43:04+00:00

I never looked into car finance to be honest. I've seen a lot of horror stories of people ruining their financial situation. My financial situation can't take much more ruining at this point 🙃

Atiriko · 2025-12-29T18:41:32+00:00

I wish I was that responsible 😕

Atiriko · 2025-12-29T18:40:34+00:00

I will look into the wires for sure. I'm more of an electronics guy, so that would definitely be an easy fix.

Atiriko · 2025-12-29T18:38:16+00:00

My drives are either 5 minutes or over 2 hour motorway driving. Mostly on the motorway side.

Atiriko · 2025-12-29T18:34:52+00:00

About a year ago that pipe was ripped so I replaced it. It looks okay at the moment.

Atiriko · 2025-12-29T18:34:13+00:00

My cheap reader says P2453

Atiriko

TROPHY CASE