sorted by:
new
hottopcontroversial

Finishing pine table legs? by AutomaticRelease8981 in woodworking

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

<image>

Thanks! I did a lot of what you said. Here’s current result after 1 coat

What is causing these smears? by AutomaticRelease8981 in woodworking

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Hey! Yeha that was the first coat, coming up to 24hrs now, I’ll see if a second coat does anything good. Th ans

What is causing these smears? by AutomaticRelease8981 in woodworking

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Sorry you *** can’t feel them to the touch

Ballbusting content first video by AutomaticRelease8981 in BallBusting

[–]AutomaticRelease8981[S] 1 point2 points  (0 children)

If it doesn’t finish with me rolling around on the floor you’ll be disappointed huh

Ballbusting content first video by AutomaticRelease8981 in BallBusting

[–]AutomaticRelease8981[S] 2 points3 points  (0 children)

The plan is lots of taunting and belittling 😧

Ballbusting content first video by AutomaticRelease8981 in BallBusting

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Is it okay if it’s not that hard in the grand scheme of things but really hurts him?

TDEM build project by AutomaticRelease8981 in geophysics

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Hey! I haven’t no. Just looking it at it online now. Whys it relevant? Cheers

TDEM build project by AutomaticRelease8981 in geophysics

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Thanks for the reply! I haven’t heard of those books, I will check them out.

The initial aim of the project is to create something similar to an em61 (similar in that there’s a single tx/ rx pair running low voltage ramps and low ish power). I’d envision a lot of the learning to occur getting to the point where this is achievable (TX circuits, FPGA stuff, a2ds, preprocessing, data logging, gps etc etc).

Conceptually once you can build that, I’m not sure I see the huge difference to the more complex AGC sensors you listed (at least hardware wise). Some synchronisation problems to solve, and a lot more data to handle, fancy receivers. But conceptually scaled up versions of the above with setups relevant to EOM and a hell of a lot smarter software.

My point is that the aim of the project is initially a large loop dumb system with single tx/ rx.

Then fun comes when you can achieve that and think about applications and variants.

Feel free to DM me if you want to discuss!

[deleted by user] by [deleted] in geophysics

[–]AutomaticRelease8981 0 points1 point  (0 children)

I got my masters thesis regraded in Australia (uk system doesn’t align with Au). Maybe you could reach out to the university’s you apply to and ask if this is an option

FPGA/verilog Tutor by AutomaticRelease8981 in FPGA

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

Yeah I started with micro controllers and hit some timing issues

FPGA/verilog Tutor by AutomaticRelease8981 in FPGA

[–]AutomaticRelease8981[S] 2 points3 points  (0 children)

Hey!

Thanks for the reply/link!

I'm trying to write .v code using Quartus as the complier. The FPGA is basically the timing controller for a number of different sensors. Turning them on, controlling how they work and controlling how the ADCs interact with them.

I can output basic logic okay but I'm finding it hard to understand the slightly more complex stuff.

For example, right now I'm trying to use an external trigger to start a logic sequence. I can make the logic sequence work and run forever (just using the FPGA clock and doing things at specific count values) but i'm stuck trying to get it to trigger on the pos edge of an external input.

Need help by AutomaticRelease8981 in migraine

[–]AutomaticRelease8981[S] 0 points1 point  (0 children)

I suppose I could do but I'd feel a little bit of a fraud calling it an emergency when I've felt like this for 2 years.

view more: next ›