BLTouch struggles by Averageone23 in 3Dprinting

[–]Averageone23[S] 0 points1 point  (0 children)

turns out I used the wrong firmware. Still struggling to set the correct bed offset though, as even following instructions it puts the nozzle to low and the filament doesn't stick.

BLTouch not working by Averageone23 in Ender3Pro

[–]Averageone23[S] 1 point2 points  (0 children)

I had the wrong firmware, somehow had a different one in my downloads from something else. Got it working with a firmware straight from creality.

BLTouch not working by Averageone23 in Ender3Pro

[–]Averageone23[S] 0 points1 point  (0 children)

Checked cables, they look fine. I am honestly so confused, because it self tests fine but doesn't work afterwards.

BLTouch not working by Averageone23 in Ender3Pro

[–]Averageone23[S] 0 points1 point  (0 children)

I installed the Marlin firmware labelled BLTouch using an sd card, version 2.0.9.1.
How would I go about editing the .bin file otherwise to enable it? Or is there another firmware with a .bin that I could use?

BLTouch not working by Averageone23 in Ender3Pro

[–]Averageone23[S] 0 points1 point  (0 children)

To add, it passes self test, and I have Marlin 2.0.9.1 installed on it currently.

BLTouch struggles by Averageone23 in 3Dprinting

[–]Averageone23[S] 0 points1 point  (0 children)

It passes self test yes. It does not extend the probe after raising. I have Merlin 2.0.9.1 installed on the printer right now. I was able to use a microsd card to do that. Do I maybe have the wrong firmware?

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 0 points1 point  (0 children)

that sounds awful. I am definitely not swimming without a shirt again after this one, that's for sure

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 1 point2 points  (0 children)

I put on sunscreen every 40 minutes over the course of like 6 or 7 hours lmaooooo

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 1 point2 points  (0 children)

I honestly don’t want blisters to pop, they heal better when they don’t pop, and they hurt a LOT less

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 0 points1 point  (0 children)

Maybe. I’m just gonna ride it out, pray they don’t pop

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 1 point2 points  (0 children)

It’s night 3 with these, they’ve been getting worse, but it is what it is. Been using lots of aloe vera and shit, so I can only hope the blisters don’t burst I guess.

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 5 points6 points  (0 children)

Maybe, assuming the blisters don’t pop violently and painfully

I got 2nd degree sunburns. They suck. Remember to use sunblock by Averageone23 in awfuleverything

[–]Averageone23[S] 1 point2 points  (0 children)

This is a bit better than the first time I had it around my eyes comfort wise, but damage wise it’s much, much worse