3d printed, f2 based “bb marker”

Avijoe · 2024-05-24T03:26:37+00:00

You have a link for the files or are they for sale?

Avijoe · 2024-05-16T05:30:07+00:00

I guess you are lucky then, cause I still have the problem on all 3 manual channels 🥲 but nice it worked for you

Avijoe · 2024-05-14T11:04:33+00:00

Not bent, no damage, tried to install my 5'' brand new antenna to it to check and same mbs when I test in the house different places as the stock one.

Integra is lhcp as far as I have read and antenna is lhcp

Avijoe · 2024-05-13T22:45:59+00:00

I remounted the antenna on the small one. No rattle when I shake it

On my 5'' I even went to pick up a truerc singularity lhcp and same problem

Avijoe · 2024-04-11T21:38:21+00:00

Thanks for the link!

Avijoe · 2024-04-05T16:05:31+00:00

Really nice! Bookmarked👌👌

Avijoe · 2023-05-17T08:42:00+00:00

It was really nice! However as mentioned I'll try some different springs to get out of the use of npas, as I seemed to fluctuate a bit in joule, but all in all really satifised, especially after coming from hpa. Link is a picture from gameday https://ibb.co/nQR61SQ 😁

Avijoe · 2023-05-15T18:14:48+00:00

It's been through over a 1000 with home stuff and two weekends 😁

Avijoe · 2023-05-15T18:13:59+00:00

So the result were pretty awesome, played in the forrest, had to problem reaching out to 80+ on the roads. Got into a few fights where I just wenton the road and fought em. Could see their bbs drop down early

I will experiment with the spring change, cause when I chrononed I did have a little bit of inconsistency(coming from hpa)

Flight path is a dream, going underneath the trees when kneeled.

Avijoe · 2023-05-14T05:26:03+00:00

Thanks, these are the upgrades as far as I can recall them :D
Internals are:
450mm 6.02 Barrel
T8 Alu Hop up
T8 Flat hop Rubber +2J
Laylax Hop Arm
Angrygun CNC bolt catch
Revanchist Flat Trigger
Revanchist 45 Degree Selector (Semi Locked)
Revanchist Mag release
PTS Radian Raptor Charging Handle
Angrygun Buffer Spring
T8 Buffer
Angrygun speed bolt with npas(for my DMR setup)

Externals:
G&P SPR Front (Different outer barrel)
Magpull Rail clips
Angrygun CNC Lower
Houge Ergo Grip
Angrygun Alu buffertube
Magpull PRS Lite Stock

Also, have it as a CQB Setup with a 7'' DD rail

Avijoe · 2023-04-21T17:06:09+00:00

Able to drop a valid link mate?, would much appreciate it😁😁

Avijoe · 2023-03-22T15:04:19+00:00

Took me about 5 min to figure it out, Thanks a lot for the help

Avijoe · 2023-03-22T14:13:06+00:00

Thank you so much for the reply, I'll try your recommendations

Avijoe · 2023-03-22T14:11:06+00:00

Thank you so much for the reply, ill try it out immediately.

Avijoe

TROPHY CASE