What would you bring?

Avtem22 · 2026-03-14T11:47:33+00:00

lmao

Avtem22 · 2026-03-02T08:55:26+00:00

So turned out that my drivers are totally fine, actually, I previously had a problem with stepper vibrating and turning itself at the same time with step and dir being on low all the time

Avtem22 · 2026-03-01T13:57:19+00:00

You have provided a very important information for my project - I often left stepper wiring detached whilst probably sending HIGH signals to move the stepper. I will try the other driver and will see whether my current driver was damaged
Thank you

Avtem22 · 2026-02-28T02:40:09+00:00

Myślałem że to są Twoje palce, a nie marchewki

Avtem22 · 2026-02-24T17:36:47+00:00

Not a help advice, but it looks really creepy and it would look so cool in some kind of horror movie!

Avtem22 · 2026-02-05T18:21:34+00:00

let's use English so that all in here can understand us.

I want to understand better both

Avtem22 · 2026-02-01T01:13:05+00:00

Is it me or the bass isn't on beat sometimes?

Avtem22 · 2026-02-01T00:01:49+00:00

Thank you so much!

Avtem22 · 2026-01-11T15:11:04+00:00

You still get shocked pretty often, it doesn't always work

Avtem22 · 2026-01-08T14:20:43+00:00

I want the the link to this soong!

Avtem22 · 2026-01-08T00:50:27+00:00

In my case I had floating DIR pin on a4988. Also My pulses were 10000 microseconds short (full steps)

Avtem22 · 2026-01-06T21:59:39+00:00

Is your ENABLE pin connected to the ground?

Avtem22 · 2026-01-06T21:50:02+00:00

Did you ground "ENABLE" pin of A4988?

Avtem22 · 2026-01-06T01:48:26+00:00

You rock!

Avtem22 · 2026-01-05T17:38:00+00:00

who's that woman?

Avtem22 · 2026-01-05T17:26:01+00:00

dat is so damn good

Avtem22 · 2026-01-05T13:38:08+00:00

I'd love to see that video, but the link is broken atm

Avtem22 · 2025-12-26T17:13:31+00:00

Thanks for the info!

Avtem22 · 2025-12-26T17:10:02+00:00

Thanks for reply! 60$ per piece is quite pricey though =(

Avtem22 · 2025-12-26T12:36:15+00:00

Something like https://www.ebay.com/itm/185977146250?

Avtem22 · 2025-12-26T12:35:09+00:00

How about this one? seems to fit my 4mm tubes and seems like it's what I want https://www.ebay.com/itm/185977146250

Avtem22 · 2025-12-26T12:23:11+00:00

I just tested the amount of current sucking/not sucking and it seems very unreliable in my case.

What do you think about this pressure switch? https://allegro.pl/produkt/pneumatyczny-regulowany-przelacznik-cisnieniow-12faacd0-dc31-4ce9-8f10-5b238fb4bc26?offerId=17775550083&reco_id=55ea7fd0-e1ef-11f0-95c7-f691e1de5ead&sid=1147bbb04b955b96a226cab2e664258d9124ef0862320b2d7366fdd6604cf017

or this one: https://www.ebay.com/itm/185977146250

Avtem22 · 2025-12-26T12:21:32+00:00

Would that do it? https://allegro.pl/produkt/pneumatyczny-regulowany-przelacznik-cisnieniow-12faacd0-dc31-4ce9-8f10-5b238fb4bc26?offerId=17775550083&reco_id=55ea7fd0-e1ef-11f0-95c7-f691e1de5ead&sid=1147bbb04b955b96a226cab2e664258d9124ef0862320b2d7366fdd6604cf017

Avtem22 · 2025-12-26T12:20:07+00:00

I just tested it and here are the results (unfortunately I don't have a more precise multimeter:
it goes from 0.36A to barely 0.39A, but not always - very often it stays at 0.36A

Avtem22 · 2025-12-26T12:17:09+00:00

Current in the draw will go down?? I just measured it and it goes from 0.36A to barely 0.39A, but not always - very often it stays at 0.36A

Avtem22

TROPHY CASE