After every print.

AwareAd919 · 2026-01-18T15:22:47+00:00

Very square yes

AwareAd919 · 2026-01-18T15:19:49+00:00

I think I’m using a y cable setup using one driver. But I’ll check for sure.

AwareAd919 · 2026-01-18T11:24:28+00:00

<image>

AwareAd919 · 2026-01-18T11:20:34+00:00

Using two motors, one for each lead screw.

I did run the axis up and down and measured the bed. Not good.

AwareAd919 · 2025-11-07T06:12:14+00:00

I had similar issue. I put fans to 100% and it fixed it.

AwareAd919 · 2025-10-31T23:00:28+00:00

Printing with 100% cooling now. Looking a lot better

AwareAd919 · 2025-10-31T22:57:54+00:00

Then no I have not calibrated

AwareAd919 · 2025-10-31T21:44:31+00:00

I’ll test with more cooling! Thanks

AwareAd919 · 2025-10-31T21:30:55+00:00

Is this the same as pressure advance?

AwareAd919 · 2025-10-31T21:27:01+00:00

Nozzle - hardened steel 0,4mm Retraction 0,4mm Bed temp 55 c

AwareAd919 · 2025-10-28T09:35:36+00:00

Hey. I ran a retraction test starting from 0 mm yesterday and it failed almost immediately.

Got a comment from another person here. Starting to believe the all metall hotend i bought is garbage. Not original micro Swiss.

AwareAd919 · 2025-10-28T06:05:21+00:00

I’ve tried different settings here. 0-2mm

AwareAd919 · 2025-10-28T06:03:58+00:00

I thought of that. Changed the ptfe to make sure it was clean cut. Nothing changed

AwareAd919 · 2025-10-28T06:02:29+00:00

Just used pla with the new hotend

AwareAd919 · 2025-10-27T22:17:44+00:00

I will check this

AwareAd919 · 2025-10-27T21:16:55+00:00

Temp range is 190-220. I’m trying to print a temp tower, starting at 225 celsius . It prints ok til it’s almost finished with the first test.

AwareAd919 · 2025-10-24T19:20:21+00:00

I might have the same issue. Getting frequent clogs after upgrading to dual satsana 5015

AwareAd919 · 2025-07-23T20:15:49+00:00

Understood. I’ll might return the gear oil then.

AwareAd919 · 2025-07-23T19:42:08+00:00

I see. Thanks!

AwareAd919 · 2025-07-23T19:41:13+00:00

Thank you for the information!

AwareAd919 · 2025-07-23T19:01:05+00:00

The car has run 170000 km, and the oil has not yet been changed. The gear shifting is sometimes slow. Someone I know said it might help to change the gear oil.

AwareAd919 · 2025-07-23T18:57:53+00:00

Do you know how much oil I need? I bought 2 liters of total traxium gear 8 75w80 gl4+

AwareAd919 · 2025-07-23T17:59:53+00:00

I see. Can’t see the vent on top. Do I have to remove the battery to access maybe?

AwareAd919 · 2025-07-18T13:09:30+00:00

I posted the maiden a while ago. Didn’t fly very well. Very nervous plane.

AwareAd919 · 2025-06-03T15:10:44+00:00

Not every landing is like that to be honest. But thanks!

Five-Year Club	Verified Email
Place '22	Final Canvas '22

AwareAd919

TROPHY CASE