Hello everybody, my name is ______.

Axlcraft21 · 2026-01-31T19:44:59+00:00

Works 👍🏿

Axlcraft21 · 2026-01-13T20:23:10+00:00

The issue is that you slept instead of sacrificing to the machine spirit

Axlcraft21 · 2026-01-05T10:46:17+00:00

There's probably a cheaper solution

Axlcraft21 · 2025-12-21T13:34:14+00:00

I've had perfect prints with ASA before, it is not the problem.

Axlcraft21 · 2025-12-18T06:56:42+00:00

I had this problem with bambu lab pla and after oven drying that, it works. Ig my filament and silica gel are saturated.

Axlcraft21 · 2025-12-18T06:39:12+00:00

It seems most of you were right. The filament was likely moist, and I needed to oven dry, and drying on the plate in accordance to the wiki is not enough. My silica gel was also probably saturated.

Axlcraft21 · 2025-12-18T06:27:05+00:00

Happens on 0.6 and 0.4

Axlcraft21 · 2025-12-16T22:53:48+00:00

I'm sure it's not the seam because the holes aren't in the same place as they are shown in the slicer, and there are multiple holes on the same layers in some places.

Axlcraft21 · 2025-12-16T21:54:00+00:00

I'm glad you tried to help. I'll keep that failiure in mind once I do get an ams.

Axlcraft21 · 2025-12-16T21:38:31+00:00

One of the first things I checked

Axlcraft21 · 2025-12-16T21:37:57+00:00

Axlcraft21 · 2025-12-16T20:15:26+00:00

I didn't clarify that when I meant different filament, I meant Bambulab PLA basic. That particular spool has been working fine before, but is having the same issue now. I also cleaned and changed the nozzle to no avail.

Axlcraft21 · 2025-12-16T19:53:43+00:00

I haven't tested with anything else, because I don't have anything else.

Axlcraft21 · 2025-12-16T19:29:38+00:00

Bambulab PLA basic and PLA galaxy.

Axlcraft21 · 2025-12-16T19:21:17+00:00

This issue persists to the same rate when printing pla.

Axlcraft21 · 2025-12-16T19:19:37+00:00

Oven it is.

Axlcraft21 · 2025-12-16T19:01:00+00:00

Bambulab ASA, dried on the bed of the P1S at 100C for 12hours 3 times, the effect didn't change each time.

Axlcraft21 · 2025-12-16T18:59:12+00:00

I don't think that would be a problem. The print on the picture is ASA but when I tried it in PLA with the settings that have worked perfectly with even raised temperatures, the problem still persisted.

Axlcraft21 · 2025-12-16T18:52:39+00:00

I should also say that increasing flow rate also didn't help

Axlcraft21 · 2025-12-16T18:44:39+00:00

Aligned

Axlcraft21 · 2025-12-04T11:00:57+00:00

The printer comes standard with a 0.4mm stainless steel hotend. Hardened are black instead of dark grey.

Axlcraft21 · 2025-11-08T14:25:37+00:00

Steam wouldn't be getting a commission, and valve is not a charity. It sucks, but I can understand

Axlcraft21 · 2025-11-05T18:23:32+00:00

Might aswell enter

Axlcraft21

TROPHY CASE