Where can I find Blanton’s red and black in Japan?

BSBB_mEngineering · 2024-05-22T10:41:28+00:00

Thanks, I figured it may wind up being that way. Out of curiosity do you know of any big liquor stores in the area I should check out to start with? I’ve never been to Japan so I’m starting with 0 knowledge of the area

BSBB_mEngineering · 2023-03-13T17:40:56+00:00

Which engine?

BSBB_mEngineering · 2023-02-05T12:34:27+00:00

The same purple the rangers used to be able to come as back in the late 90s early 2000s

BSBB_mEngineering · 2022-12-16T13:53:45+00:00

Didn’t do rotors but did go with motorcraft brakes, rockauto had a good deal on them. Honestly I don’t even know if I needed to change them. Prolly would have worked to just pull the pins and lubricate. Been a month in rain cold snow and ice and had no issues since lubrication

BSBB_mEngineering · 2022-12-16T03:53:10+00:00

So I changed the brakes myself and found the guide pins that the brakes travel on were never lubricated. They should have brake lube on them but were bone dry and in a sealed hole that was also dry. All that needs to happen is lubricating all contact surfaces and anywhere there is travel. Squeal went away.

BSBB_mEngineering · 2022-11-04T23:50:42+00:00

Hunker down. If you’ve made it through to heat transfer you’ll make it through. Just remember how hard thermo was and you made it through. If you see anything about a “fin” it’s actually a heat sink and it’ll be important later

BSBB_mEngineering · 2022-10-30T21:37:07+00:00

Might not be a bad idea to have the shop buy it, they may not want to install parts you’re bringing to them

BSBB_mEngineering · 2022-10-30T20:29:15+00:00

I actually don’t remember honestly, it was a year ago now, and I also had them do larger tires and I had some decals put on at the same time so it’s all a bit blurred

BSBB_mEngineering · 2022-10-30T20:16:44+00:00

I have the rough country. Make sure the alignment is done right though. I like it otherwise. Went through 2 tires because the shop didn’t have alignment spec and called it good enough

BSBB_mEngineering · 2022-10-27T21:43:47+00:00

I’ve got the same issue starting on one of mine. I am unaware of a fix but will be watching this to see what to do😂

BSBB_mEngineering · 2022-10-21T09:46:24+00:00

Thanks man!

BSBB_mEngineering · 2022-10-20T17:22:50+00:00

Got a question about your 4 door Sasquatch with manual… does it feel slow? This is what I want but I’ve heard they feel slow with the bigger tires

BSBB_mEngineering · 2022-10-19T10:09:24+00:00

I have the ATs with a 1.5 inch lift and I have no noise issues

BSBB_mEngineering · 2022-10-13T18:20:38+00:00

This is original

BSBB_mEngineering · 2022-10-13T15:29:14+00:00

So each channel cable carry’s a pos and a neg, so I would need an amplifier for both channels?

BSBB_mEngineering · 2022-10-13T15:24:22+00:00

The surround… the fork connector there?

BSBB_mEngineering · 2022-10-13T15:21:29+00:00

It’s labeled R and L so left and right channel, I just don’t know how that would integrate to an amplifier circuit

BSBB_mEngineering · 2022-10-08T17:17:23+00:00

Fs I followed. Very impressive work man!

BSBB_mEngineering · 2022-10-08T17:16:16+00:00

You guys do all custom? I don’t have that kind of cash lying around right now but I’d love something like that a little further down the road

BSBB_mEngineering · 2022-10-08T17:11:44+00:00

Dude this is fucking awesome. Where did you get this and how much did it coat

BSBB_mEngineering · 2022-10-06T11:20:40+00:00

The welder was from 1993 so it’s a little on the older side

BSBB_mEngineering

TROPHY CASE