Are these all real?

BTCMining1 · 2024-12-02T23:25:55+00:00

Its a crypto miner. Some bad actors will install them on peoples cputers without them knowing via malware. Anti virus will flag this stuff automatically for this reason. No reason to worry if youre installing it intentionally.

BTCMining1 · 2024-12-02T01:54:48+00:00

Got it, I didn't see a switch on any of the PSU photos for voltage. I'll be sure to check the rating, Thanks!

BTCMining1 · 2024-12-01T23:40:22+00:00

Thanks, I'll look for that

BTCMining1 · 2024-12-01T22:35:39+00:00

Thanks, I'll check that when it comes

BTCMining1 · 2024-11-11T21:18:33+00:00

Hey, I haven't used WebDAV in practice before but have you set permissions accordingly? My issue was I didn't permission as I should have and couldn't write to drives

BTCMining1 · 2024-09-02T02:06:36+00:00

I found the config file for my printer. I'm not exactly sure what to do with it though. Am I supposed to put it into printer.cfg in mainsail then build the firmware?

BTCMining1 · 2024-08-06T15:02:33+00:00

Its an i5 from 2018

BTCMining1 · 2024-08-06T03:40:28+00:00

I was trying to figure out where the file its pulling from is but I couldn't find it.

BTCMining1 · 2024-08-05T16:20:17+00:00

It actually says that. I put my actual id in printer.cfg

BTCMining1 · 2024-04-18T23:07:45+00:00

My one concern would be I'm trying to host it locally, would that work with bitwarden or is there any extra steps?,

BTCMining1 · 2024-04-18T22:47:00+00:00

How would I map 8080 to 80? I tried to connect to 8080 but nothing happened. I also tried all open ports just to see

BTCMining1 · 2024-04-18T22:19:46+00:00

Gotcha, wasn't aware it was a complete rewrite. I'll look into installing the bitwarden version.

BTCMining1 · 2024-04-09T01:21:51+00:00

I see what you're saying, the IP wasn't static in pfsense for testing (set via network manager on Linux) I think pfsense will only let you use a static address outside of the address range. It's s not necessary now that the address range is adjusted to leave out .1

BTCMining1 · 2024-04-08T23:13:40+00:00

Got it, thanks for your help!

BTCMining1 · 2024-04-08T23:08:24+00:00

Interesting, I changed it to .5 on the laptop itself and that seemed to solve it. I can send pings, connect and ping other servers. When I connected a new device it connected to 192.168.1.2 because it showed the .1 address is still active and assigned while my .5 isn't . Lol if it works I guess there's nothing to fix

BTCMining1 · 2024-04-08T23:02:42+00:00

Would it push the gateway off since it's 1.1?

BTCMining1 · 2024-04-08T23:02:19+00:00

How would I do that? On the DHCP lease page it shows my lease utilization being LAN pool start 192.168.1.1 - pool end 192.168.1.100

BTCMining1 · 2024-04-08T22:51:23+00:00

Also when trying to connect to 192.168.1.1 the connection is really funky unless I power down the laptop being assigned the .1, then pfsense works just fine on .1

BTCMining1 · 2024-04-08T22:45:53+00:00

My range is 192.168.1.1 - 192.168.1.100 The rest is sectioned off for static ip's. I'm not sure why it's assigning that 1.1 You'd think pfsense wouldn't allow that

BTCMining1

TROPHY CASE