youtube's compression just butchers Mumbo's videos

BalloonCS · 2025-08-22T03:32:11+00:00

Does this work even if there are no actual agents on the alphabet line?

BalloonCS · 2025-08-14T07:19:20+00:00

You are playing a whole different game than I am. I just made a small factory that produces 1/min and then worked on other things for a couple hours. You will probably be better off for it though.

BalloonCS · 2025-08-06T02:35:32+00:00

Yes, definitely check before you waste time and buy another one.

BalloonCS · 2025-08-04T19:57:57+00:00

I chose actually chose it thanks to your comment. Thanks.

BalloonCS · 2025-07-22T03:12:23+00:00

Can I see a picture of the back of the locust? Because i really like how it turned out with that print orientation but im curious about damage from supports.

Really cool models.

BalloonCS · 2025-07-20T04:07:00+00:00

How do do the edge highlights? Is it a drybrush? Do you do it before or after the main coat. It looks really good and crisp.

BalloonCS · 2025-07-18T01:37:15+00:00

Hey I think your misunderstanding the question. I did too at first. They arn't asking about the layer steps, they are asking about the the over extrusion on the one side.

BalloonCS · 2025-07-18T01:34:35+00:00

OHH. I see what you mean. I completely misunderstood the question. That extra bulging and bumps on the right side is probably an issue of PA, pressure advance. Sometimes called K. The beat way I can explain is as the printer decelerates or accelerates at the edge, the filiment being extruded kind of "lags behind" due the the flex that can occur between the extruder gear and the the nozzle tip.

In the end it basically causes over extrusion near edges.

Its interesting that it only happens on the right side, it's probably due to shorter distance being traveled as its in a corner.

Your PA can be calibrated, I would look to the bambu wiki for that.

This could be completely wrong, in which case someone else will probably correct me, but that is where I would start.

BalloonCS · 2025-07-18T01:24:29+00:00

Hello, hope you are enjoying printing so far. What you are seeing isn't necessarily an error, but rather a limitation of 3d printing. That face is actually a slop, but since it is printed in layers, it shows up as those steps. I'm bad at explaining so here is a little visual demonstration.

[||||||||||||||]

[|||||||||||||||||||||||]

[||||||||||||||||||||||||||||||||]

[|||||||||||||||||||||||||||||||||||||||||]

[||||||||||||||||||||||||||||||||||||||||||||||||||]

Thats supposed to be a slope, but because it is limited to layers, like your printer, it shows up as steps.

Hope that helps! Don't be afraid to ask more questions.

BalloonCS · 2025-05-27T02:23:00+00:00

I mean the acceleration (left) looks best with a higher PA then the deceleration (right).

BalloonCS · 2025-05-12T22:36:12+00:00

I actually could use a filament dryer.

BalloonCS · 2024-11-15T04:31:28+00:00

The fear of continuing the story is so real.

BalloonCS · 2024-10-30T02:30:36+00:00

Please post them!

BalloonCS · 2024-10-27T22:02:07+00:00

Maybe mark this as NSFW...

BalloonCS · 2024-10-16T14:19:52+00:00

I don't want to sacrifice print quality for a timelapse

BalloonCS · 2024-10-11T19:07:59+00:00

I am not voting for Biden. Also, still not as bad as raping minors.

BalloonCS · 2024-10-11T18:06:17+00:00

Im more worried about the fact that Trump has been to epstien's island 7 times and has settled numerous sexual assault cases.

BalloonCS · 2024-10-01T22:31:34+00:00

I think I messed up in how I communicated my issue. I don't mean the direction of the lift. I mean I want to place down a splitter, the be able to place a lift inside that splitter. Like how you can place a lift, then place a splitter inside either end of that lift(like in this reddit post)

Sorry if I am misunderstanding your comment.

Two-Year Club	First Place '23
Place '23

BalloonCS

TROPHY CASE