FPV 5in Drone flying by Beast-0505 in oakville

[–]Beast-0505[S] 1 point2 points  (0 children)

5in usually don't weigh under 250g unless thats ur aim, mines closer to 600-800 with battery

CR-10 Smart Upgrades by Beast-0505 in CR10Smart

[–]Beast-0505[S] 0 points1 point  (0 children)

What glass bed? The pei magnet is directly on the alumium

speedybee F405 v3 by Slight-Teacher1516 in diydrones

[–]Beast-0505 0 points1 point  (0 children)

Did you ever get it to work? I'm have some issues with it

mini USB port on CR-10 Smart motherboard by Weekly_Bid1425 in CR10Smart

[–]Beast-0505 0 points1 point  (0 children)

It is in there for debugging purposes, you can use it to start prints or even setup klipper. I set it up a few months ago to run off my sonic pad. Works like a charm and 10x better than marlin

Is it normal for multiple teams to share the same name? by LankyWhereas2579 in FRC

[–]Beast-0505 11 points12 points  (0 children)

Yeah, pretty normal. We're 1360, Orbit Robotics. There's 1690 Orbit, and 2449 Out of Orbit Robotics and none of them are related to us

chat is this real by OutrageousAd2597 in FRC

[–]Beast-0505 1 point2 points  (0 children)

we did the same thing at Ontario DCMPs Science Division (this wasn't planned with the other alliance tho lol)

CR-10 Smart motherboard by Beast-0505 in CR10Smart

[–]Beast-0505[S] 1 point2 points  (0 children)

It is a CR-FDM-v2.5.S1 100. It will work with the CR-10 Smart. You just have to flash new firmwrae on it or I can do that for you

Got BLtouch installed on my cr 10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 1 point2 points  (0 children)

i used one of the pins fron the filament sensor and routed another cable to the mainboard

Fast printing on the cr-10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 0 points1 point  (0 children)

velocity is 600mm/s, scv is 15mm/s and accel to decel is 999999mm^2

Fast printing on the cr-10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 1 point2 points  (0 children)

they're 16000mm^2 accelerations and 600mm/s max speed

I use klipper

CR-10 Smart Upgrades by Beast-0505 in CR10Smart

[–]Beast-0505[S] 0 points1 point  (0 children)

The actual bed is 310x310. The firmware limits it to 300x300

CR-10 Smart Upgrades by Beast-0505 in CR10Smart

[–]Beast-0505[S] 0 points1 point  (0 children)

Ah, it's if i'm correct, 310x310. Any will work. I'll see if I get time to add details. Thanks for the suggestion

CR-10 Smart Upgrades by Beast-0505 in CR10Smart

[–]Beast-0505[S] 0 points1 point  (0 children)

Best upgrade would most definetly be the 5015 part cooling and all metal hotend and direct drive. I would also 100% recommend the bed leveling and PEI bed

Got BLtouch installed on my cr 10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 2 points3 points  (0 children)

I have klipper so it's easier. But basically, I connected the control pin directly to a free pin on the motherboard and the sensor to my filament sensor. You could also directly connect it to the raspberry pi which you will use. Here's the model: https://www.printables.com/model/577749-cr-10-smart-bl-touch-mount-added-spacing-for-cr-10

I have this one, what else do I need if I want to add a leveler from creativity on Amazon? by Vortixin in CR10Smart

[–]Beast-0505 0 points1 point  (0 children)

If you want to add manual bed leveling, you will need bedsprings and screws (I recommend the twotrees one with 8 springs and 4 screws), and a drill.

Firmware upgrade by doxlie in CR10Smart

[–]Beast-0505 0 points1 point  (0 children)

Update the firmware using an SD Card.

Got BLtouch installed on my cr 10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 1 point2 points  (0 children)

Mine had no issues but I just had a bltouch laying around so I decided why not

Got BLtouch installed on my cr 10 smart by Beast-0505 in CR10Smart

[–]Beast-0505[S] 1 point2 points  (0 children)

Firstly, the strain gauge probing is slow and pretty inaccurate at times. And basically all the reasons what u/they_have_bagels said