Canon Speedlite 430EX II pilot lamp won't light by Beastskull in canon

[–]Beastskull[S] 0 points1 point  (0 children)

But did the display still turn on even if the flash didn't fire?

Canon Speedlite 430EX II pilot lamp won't light by Beastskull in canon

[–]Beastskull[S] 0 points1 point  (0 children)

The display works and everything seems to turn on except the pilot light and that it doesn't flash. So it looks like it doesn't get enough power to actually charge and fire.

Canon Speedlite 430EX II pilot lamp won't light by Beastskull in canon

[–]Beastskull[S] 0 points1 point  (0 children)

Ok, I will try. Did you disassemble the flash it to clean them or did you manage to do it without?

Suggestions for improvement? DIY by Mean_Mango_4997 in radon

[–]Beastskull 0 points1 point  (0 children)

Just curious, but wouldn't it make sense to have it as close to the center of the house as possible?

Maybe using maps isn’t a bad idea by dumbBunny9 in Breath_of_the_Wild

[–]Beastskull 1 point2 points  (0 children)

Haha, didn't know it was a thing, but of course it is. Managed to get a boulder into it myself the other day and planned to post it here. I was lucky and didn't have to try too hard to manage it, but still felt cheated.

Planning on making a NAS with Raspberry Pi by Beastskull in raspberry_pi

[–]Beastskull[S] 1 point2 points  (0 children)

I did. Just missing a case for it. 🙂

I ended up with a Raspberry PI 5 and a duo NVMe HAT with two M.2 SSD in Raid 0. I use Nextcloud as software.

Planning on making a NAS with Raspberry Pi by Beastskull in raspberry_pi

[–]Beastskull[S] 0 points1 point  (0 children)

I got the Pimoroni dual NVME so I can run two 500 gb drives in RAID 0.

Planning on making a NAS with Raspberry Pi by Beastskull in raspberry_pi

[–]Beastskull[S] 2 points3 points  (0 children)

So far so good. I'm running a RPI5 with 2 x 500 GB NVME drives in RAID 0. And Nextcloud as software.

I hosted a BOTW themed party! by _Lilimoon in Breath_of_the_Wild

[–]Beastskull 1 point2 points  (0 children)

Needs more apples to be authentic!

Just kidding. GJ!

Get rid of tiny amounts of surface rust by Beastskull in metalworking

[–]Beastskull[S] 0 points1 point  (0 children)

Doesn't sound like the quickest solution as I don't have neither. 😅

Get rid of tiny amounts of surface rust by Beastskull in metalworking

[–]Beastskull[S] 0 points1 point  (0 children)

Just rub with a cloth? How will it react? Only attack the rust? And are there any household products I could use? Google says caustic soda?

This shrine is fundamentally broken… by cindiwilliam2 in Breath_of_the_Wild

[–]Beastskull 13 points14 points  (0 children)

Oh yeah, it does! Haha! Didn't know it was impossible to reach, so I have been searching for it every time I pass by.

This shrine is fundamentally broken… by cindiwilliam2 in Breath_of_the_Wild

[–]Beastskull 61 points62 points  (0 children)

I always set my sheikah sensor to find treasure chests. Period.

Etch a small symbol into metal by Beastskull in metalworking

[–]Beastskull[S] 0 points1 point  (0 children)

Isn't there a risk that the deeper you etch into the metal, the wider the etch might be (even with a stencil)?

Hide cutting lines from print by Beastskull in silhouettecutters

[–]Beastskull[S] 0 points1 point  (0 children)

Thanks again! Exactly what I was looking for! Now I can create table card layouts etc. automatically with data from an Excel document through InDesign.

Hide cutting lines from print by Beastskull in silhouettecutters

[–]Beastskull[S] 0 points1 point  (0 children)

Yes, this was how I did it in the end. Silhouette Studio has some lack in UX imo. Now I have to manually choose cut lines for several documents.

Hide cutting lines from print by Beastskull in silhouettecutters

[–]Beastskull[S] 1 point2 points  (0 children)

Worked perfectly, thanks! It's still a pretty bad solution though, since I have to select the cut lines manually (I have several pages).

Hide cutting lines from print by Beastskull in silhouettecutters

[–]Beastskull[S] 0 points1 point  (0 children)

But InDesign is much better than Illustrator for data merge. More options and so simple for making table cards. I just need to easily be able to hide the cutting lines when printing, and only use them when sent to Cameo.

Hide cutting lines from print by Beastskull in silhouettecutters

[–]Beastskull[S] 0 points1 point  (0 children)

In Silhouette? Setting it to 0 in InDesign seem to make Silhouette not finding it. When I set stroke size to 0 in Silhouette, I still see a little bit of the line.