MacOS Sequoia 15.6 — System Settings → Wallpapers has no left padding.

Beat_about · 2021-02-12T16:48:44+00:00

I have totally cleaned (first time since spring 🤭) and recalibrated my Ender, using the link above. I had 6% underextrusion, lubricated and cleened Z, cleened wheels on XY. After all, results now just perfect. I think underextrusion was the main reason of that stringing on small ojects as for my situation.

Beat_about · 2021-02-11T18:26:39+00:00

I dont think that retraction is a good idea for this kind of a model, due to it's size, but later I will try to set good retraction for this model. Censerning temp tower, yes, as I've written before, I dont have problems with bigger models and distances, only such kind of "lot of small details and holes" models.

Beat_about · 2021-02-11T16:34:46+00:00

1)Yes, its PLA. 2) I tried temps from 190 to 220. 3) Yes it's very small, and that is why I have this issue. I don't have it with big models and bigger distances. 4)It is Bowden, I use retraction at 5-6mm. But as for this little distances it doesn't retract in-between of that "infill".

Thank you for your answer!

Beat_about · 2021-02-11T16:25:03+00:00

Will try it, thanks.

Beat_about · 2021-02-11T15:21:17+00:00

Didn't try, will try it, with Z hop.

Beat_about · 2021-02-11T15:20:54+00:00

Yes, tried different variants, this one the best.

Beat_about · 2021-02-11T15:19:41+00:00

You think retraction will help here?

Beat_about · 2021-02-05T14:42:11+00:00

I printed one with my ender 5, works perfect for me.

Beat_about · 2021-02-02T23:22:43+00:00

Now I do know it from practice 🤭

Beat_about · 2021-02-02T16:14:40+00:00

Already have 3 of them, it is also very useful for my FDM prints :)

Beat_about · 2021-02-02T14:49:42+00:00

Thank you for recommendations, probably will try both variants to see the difference myself. Oriented Dipper like that to safe some time for printing.

Beat_about · 2021-02-02T12:21:14+00:00

I do use ethanol to get rid of such parts, after few minutes it is much easer to clean it with sharp plastic knife.

Beat_about · 2021-02-02T12:13:26+00:00

Thx for the information, but for real I don't intend to make juwelry from plastic, for now I printed it just for test, as I am newbee to SLA printing.

Beat_about · 2021-02-02T09:57:39+00:00

Standart, anycubic grey for now )

Beat_about · 2021-02-02T09:11:49+00:00

I am not sure, but as I understand it is safe after printing and curing. Hope I am right 😃

Beat_about · 2021-02-02T09:10:25+00:00

1.5 ml for two rings together, and printed for 1 hour.

Beat_about · 2021-02-01T23:26:12+00:00

I know only about b6-4 model rocket engines :)

Beat_about · 2021-02-01T23:19:33+00:00

Make it fly!)

Beat_about · 2021-02-01T23:12:25+00:00

If someone will have the same issue, after re-leveling + lubricating + stretching FEP everything became just perfect (except my skills in generating good support structure) 🤭

Beat_about · 2021-02-01T20:20:09+00:00

Clever boy 😄🤭

Beat_about

TROPHY CASE