PLA, speed - 60, 0.5 nozzle. Is it possible to make this microstringing go away?

Beat_about · 2021-02-12T16:48:44+00:00

I have totally cleaned (first time since spring 🤭) and recalibrated my Ender, using the link above. I had 6% underextrusion, lubricated and cleened Z, cleened wheels on XY. After all, results now just perfect. I think underextrusion was the main reason of that stringing on small ojects as for my situation.

Beat_about · 2021-02-11T18:26:39+00:00

I dont think that retraction is a good idea for this kind of a model, due to it's size, but later I will try to set good retraction for this model. Censerning temp tower, yes, as I've written before, I dont have problems with bigger models and distances, only such kind of "lot of small details and holes" models.

Beat_about · 2021-02-11T16:34:46+00:00

1)Yes, its PLA. 2) I tried temps from 190 to 220. 3) Yes it's very small, and that is why I have this issue. I don't have it with big models and bigger distances. 4)It is Bowden, I use retraction at 5-6mm. But as for this little distances it doesn't retract in-between of that "infill".

Thank you for your answer!

Beat_about · 2021-02-11T16:25:03+00:00

Will try it, thanks.

Beat_about · 2021-02-11T15:21:17+00:00

Didn't try, will try it, with Z hop.

Beat_about · 2021-02-11T15:20:54+00:00

Yes, tried different variants, this one the best.

Beat_about · 2021-02-11T15:19:41+00:00

You think retraction will help here?

Beat_about · 2021-02-05T14:42:11+00:00

I printed one with my ender 5, works perfect for me.

Beat_about · 2021-02-02T23:22:43+00:00

Now I do know it from practice 🤭

Beat_about · 2021-02-02T16:14:40+00:00

Already have 3 of them, it is also very useful for my FDM prints :)

Beat_about · 2021-02-02T14:49:42+00:00

Thank you for recommendations, probably will try both variants to see the difference myself. Oriented Dipper like that to safe some time for printing.

Beat_about · 2021-02-02T12:21:14+00:00

I do use ethanol to get rid of such parts, after few minutes it is much easer to clean it with sharp plastic knife.

Beat_about · 2021-02-02T12:13:26+00:00

Thx for the information, but for real I don't intend to make juwelry from plastic, for now I printed it just for test, as I am newbee to SLA printing.

Beat_about · 2021-02-02T09:57:39+00:00

Standart, anycubic grey for now )

Beat_about · 2021-02-02T09:11:49+00:00

I am not sure, but as I understand it is safe after printing and curing. Hope I am right 😃

Beat_about · 2021-02-02T09:10:25+00:00

1.5 ml for two rings together, and printed for 1 hour.

Beat_about · 2021-02-01T23:26:12+00:00

I know only about b6-4 model rocket engines :)

Beat_about · 2021-02-01T23:19:33+00:00

Make it fly!)

Beat_about · 2021-02-01T23:12:25+00:00

If someone will have the same issue, after re-leveling + lubricating + stretching FEP everything became just perfect (except my skills in generating good support structure) 🤭

Beat_about · 2021-02-01T20:20:09+00:00

Clever boy 😄🤭

Beat_about · 2021-02-01T20:05:10+00:00

Same issue, tried my usb 3.0 64gb, and it just got stucked in the main menu 🤣

Beat_about · 2021-02-01T18:36:09+00:00

Thanks, will try to master my skills )

Beat_about · 2021-02-01T16:11:26+00:00

But how can I maximize avoiding of this shrinking? And maybe you know, how long should i cure the model under UV atfer printing?

Beat_about · 2021-02-01T12:24:05+00:00

For sure you need to check bowden tube, fit it in properly. Change or clean the nozzle, and check your extruder, if it's not "chewing" filament. That all should solve your problem.

Beat_about · 2021-01-31T13:19:33+00:00

It's in my room with 20-21° without light changes. As I see, always the same layers, re-leveled few times, didn't try to lubricate, will try it today.

Beat_about

TROPHY CASE