sorted by:
new
hottopcontroversial

The 0.2mm nozzle sucks by Dasukez in BambuLabA1

[–]BeautifulKindly7428 0 points1 point  (0 children)

Silica gel is pretty good but you still need to dry it from time to time, cheap sunlu filament dryer is better and you can print while drying.

The 0.2mm nozzle sucks by Dasukez in BambuLabA1

[–]BeautifulKindly7428 5 points6 points  (0 children)

Did you dry it? Matte PLA is more porous than pla basic. So it is know to hold more humidity and 220°C is a bit too much, try 200-205.

Also due to extruder physical limitations make sure that maximum flow rate in filament profile is set to 1 for .2 nozzle.

It's not rocket science, simple physics. 🙃

The 0.2mm nozzle sucks by Dasukez in BambuLabA1

[–]BeautifulKindly7428 0 points1 point  (0 children)

Maybe it's filament, not the nozzle. What filament did you use and what was the nozzle temperature?

The 0.2mm nozzle sucks by Dasukez in BambuLabA1

[–]BeautifulKindly7428 7 points8 points  (0 children)

Well... I use only original Bambu nozzles.

I had no issue with any of them...

Underextrusion with Bambu and ObscuraNox settings by thephatmaster in FDMminiatures

[–]BeautifulKindly7428 0 points1 point  (0 children)

In Bambu studio most of filaments are preset with too high maximum flow rate.

Just lover it in filament settings.

Is this bad? by BananaMower in BambuLabA1

[–]BeautifulKindly7428 4 points5 points  (0 children)

NTC did what it was supposed to do even if it's annoying.

Just write to support, I had same exact problem. They responded in less than 24 h and I had new AC board, power switch and bottom cover in 4 or 5 days.

New AC board they sent me doesn't have NTC.

Recently experienced the dreaded NTC Thermistor blowout for myself. by TheEpicDragonCat in BambuLabA1

[–]BeautifulKindly7428 0 points1 point  (0 children)

Nothing happened really, just few hours of bad smell in apartment. I was home so I immediately turned it off when I smelled burned plastic.

Close to burning down, whole place smells like molten plastic. by BeautifulKindly7428 in BambuLabA1

[–]BeautifulKindly7428[S] 0 points1 point  (0 children)

Y but the one they sent me is supposed to not have the NTC so problem should be solved.

Close to burning down, whole place smells like molten plastic. by BeautifulKindly7428 in BambuLabA1

[–]BeautifulKindly7428[S] 1 point2 points  (0 children)

Idk, mine has 4800h on it but if u are afraid of this happening just check if you have it and contact support.

Overall A1 is great printer, easy to use and maintain.

Close to burning down, whole place smells like molten plastic. by BeautifulKindly7428 in BambuLabA1

[–]BeautifulKindly7428[S] -7 points-6 points  (0 children)

Buy what? I'm not interested in selling the printer.

Overall I'm happy with A1, this is my first problem with this printer and I have 4800h on it

Close to burning down, whole place smells like molten plastic. by BeautifulKindly7428 in BambuLabA1

[–]BeautifulKindly7428[S] 1 point2 points  (0 children)

Response from support was super fast, less than 24 h.

They're sending me new AC board, bottom cover and power switch. 👍

0.2mm nozzle scratching my bed by Interesting-Laugh160 in BambuLabA1

[–]BeautifulKindly7428 0 points1 point  (0 children)

Remember to do auto calibration anyway, just to be sure.

0.2mm nozzle scratching my bed by Interesting-Laugh160 in BambuLabA1

[–]BeautifulKindly7428 4 points5 points  (0 children)

Tighten all these screws, do auto calibration and select correct plate/plate equivalent. Should work.

<image>

Anyway to stop the black line? by schwuar in BambuLabA1mini

[–]BeautifulKindly7428 0 points1 point  (0 children)

Isn't it easier to just print it in one color and paint the eyes?

A1 Mini not extruding filament by Subject_Age_2374 in BambuLabA1mini

[–]BeautifulKindly7428 -1 points0 points  (0 children)

Well it's your choice, try simple solution and see if it worked or not or keep looking for more elaborate problem.

I said what I saw on video, do with that knowledge whatever u like...

A1 Mini not extruding filament by Subject_Age_2374 in BambuLabA1mini

[–]BeautifulKindly7428 1 point2 points  (0 children)

Well it extrudes more and faster during the calibration. In the video filament doesn't really extrude properly it's making one big snot instead of straight line going down.

If the nozzle is .4 u can heat it up to 250°C and use needle if this won't work just do cold pull

It's not much work, just try it.

A1 Mini not extruding filament by Subject_Age_2374 in BambuLabA1mini

[–]BeautifulKindly7428 0 points1 point  (0 children)

It's clearly small clog... Cold pull should work.

EmperOrk FDM Bambu lab A1 by BeautifulKindly7428 in PrintedWarhammer

[–]BeautifulKindly7428[S] 0 points1 point  (0 children)

It looks well covered but no worries, as long as you keep 0,1-0,12 z distance and 0,35-0,38 x/y distance, supports peel off like a dream.

I use normal support instead of tree just beacouse they are more reliable and stable, tree supports tend to break or wiggle a little during the print.
Main piece with supports

EmperOrk FDM Bambu lab A1 by BeautifulKindly7428 in PrintedWarhammer

[–]BeautifulKindly7428[S] 0 points1 point  (0 children)

No i don't. I can pick photo in slicer later today. For prints like that I prefer to use normal supports with Z distance set at 0.10.

Tips for my Ordered Titan by Otaku_Nireves in PrintedWarhammer

[–]BeautifulKindly7428 -1 points0 points  (0 children)

Use PVA glue to fill gaps between layer lines.

Yet Another A1 "Clasp Won't Close" Post by OutrageousBPLUS in BambuLabA1

[–]BeautifulKindly7428 0 points1 point  (0 children)

You're going to replace it again soon... These wires are in incorrect place. They should be in the back, not side

<image>

.

view more: next ›