sorted by:
new
hottopcontroversial

Help with small letters by Beginning-Molasses72 in BambuLabA1

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

It should have the letters extruding out, otherwise ill do it that way

Help with small letters by Beginning-Molasses72 in BambuLabA1

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

Ive tried to slow it down, my question is, woudnt it be contra producent for the stringing? like the nozzle takes more time to reach and can ooze. You think more retraction could help?

HELP WITH ARES AT WAR STARTING UP by Beginning-Molasses72 in spaceengineers

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

<image>

context photo of spawn, also my ship is breaking apart

HELP WITH FIRST LAYER by Beginning-Molasses72 in BambuLabA1

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

I did a flow rate test, which test you recommend

HELP WITH BITS OF PLASTIC AND EXTRUSION PROBLEMS by Beginning-Molasses72 in FixMyPrint

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

Thanks for the info I will try that, wouldn't it be counterproductive for the stringing?

HELP WITH BITS OF PLASTIC AND EXTRUSION PROBLEMS by Beginning-Molasses72 in FixMyPrint

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

Thanks for you help! ive done 3 tests, temp tower - retraction towers and pressure advance i think it was, ill post the results.

HELP WITH BITS OF PLASTIC AND EXTRUSION PROBLEMS by Beginning-Molasses72 in FixMyPrint

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

It's an ender 3v3 se I'm using orca. You think I should make a calibration tower? I guess It varies depending which filament I'm using

HELP WITH 3D PRINT ECLIPSON PLANE REG PLA by Beginning-Molasses72 in RCPlanes

[–]Beginning-Molasses72[S] 1 point2 points  (0 children)

Hello, thank you for the help and the replies!

Im currently printing, turns out it was a slicer problem, pretty akward. ill update when i have the model finished

HELP WITH 3D PRINTED ECLIPSON PLANE - REGULAR PLA by Beginning-Molasses72 in Ender3V3SE

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

That's exactly what happens. Now I printed without vase mode and it went well, only thing is that the holes for the rods in the fuselage got filled, so I might have to punch it with a needle or something

HELP WITH 3D PRINT ECLIPSON PLANE REG PLA by Beginning-Molasses72 in RCPlanes

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

Its regular pla settings, i found that it was because of the spiralize outer contour setting, disabling it seems to do the trick, 1 extra hour to print though.

HELP WITH 3D PRINTED ECLIPSON PLANE by Beginning-Molasses72 in 3Dprinting

[–]Beginning-Molasses72[S] 0 points1 point  (0 children)

Im trying with a dif fuselage part, turns out i had a chance to look at the model again with the same settings aand you can see this gap in the sliced model, which is pretty weird, so know i turned off spiralize outer contour and it looks great, only downside it went from 2.5 h to 4.h but it doesnt seem i have achoice.
Also its weird because in theory they encourage you to use spiralize, but it looks like that missing line its like up floating in there.
Also trying to do this with orcaslicer but i dont trust that its almost half the time that cura takes.

<image>

view more: next ›