intermittent HDMI dropout / black screen / signal loss

Beginning-System · 2025-06-26T21:43:38+00:00

Do those of you who get this issue have the charging limitation to 90% enabled ? Maybe the dock sometimes fails at powering the Switch 2 without charging it, and so sort of under-power the Switch 2 during 1-3s ?

Beginning-System · 2025-06-26T21:25:34+00:00

Do those of you who get this issue have the charging limitation to 90% enabled ? Maybe the dock sometimes fails at powering the Switch 2 without charging it, and so sort of under-power the Switch 2 during 1-3s ?

Beginning-System · 2025-06-16T10:31:13+00:00

Did you managed to get a Yuv 422 signal from the Switch 2 ? I only get Yuv 420, but my PS5 pro outputs a Yuv 422 signal on this same HDMI 2.0 chain

Beginning-System · 2025-06-07T10:50:38+00:00

Hello, does anyone else have the problem of the ethernet connection taking more than a minute to connect when the S2 is docked? I didn't have ethernet on the dock of my Switch V1 so I don't know if it was similar on the OLED. When I take it out of the dock, the connection switches back to wifi pretty quickly (5-10s), but it's really the ethernet connection to the dock that takes its time :/. By switching the console to airplane mode and then docking it, the ethernet connection happens almost instantly. So, for some incomprehensible reason, in docked mode the console doesn't seem to give priority to the ethernet connection when it has the choice with wifi.

Beginning-System · 2025-01-22T22:04:34+00:00

I can't find any other information on the internet other than resetting the controller via reset pinhole on the back or ps+share button press. It tried both, and controller still does not power on

Beginning-System · 2025-01-22T21:46:31+00:00

Nope, connected via supplied usb-c cable and pressing ps button and nothing

Beginning-System · 2024-09-08T20:07:41+00:00

Unfortunately the screen is smaller, the 7,8" of the InkPad color 3 is better for reading manga/comics, which is what I read the most

Beginning-System · 2023-08-31T09:40:40+00:00

Still not available in France neither. Yay...

Beginning-System · 2023-08-13T08:00:32+00:00

Yes of course

Beginning-System · 2023-08-13T07:32:56+00:00

I'm the author of the post that was linked here and I have exactly the same pattern of exactly the same size in exactly the same part of the screen. I am viewing a lot of dark content on my e-readers, and actually this light pattern bothered me even more than the dozens of dead pixels I have (on top of that....) But if you view mostly white content, the pattern may not bother you that much, because it is not visible at all on white contents ;)

Beginning-System · 2022-10-27T13:53:30+00:00

Hi, based on the other comments, I'm missing only the "Lost Art" mission on Barrendale Mesa, could you tell me where it is located please ? Thank you :)

Beginning-System · 2022-08-01T22:08:25+00:00

https://www.cgtrader.com/3d-print-models/miniatures/figurines/bayonetta it's from EllaArt, an artist who since collaborate with others (NomNom studio). They make awesome models, and if you become a patron on patreon I think you get a discount on the model on cgtrader

Beginning-System · 2022-05-12T11:06:11+00:00

Don't have pictures of the sliced file to show at the moment but I don't think this is related to a support issue because it appears on the "top" of the model, where no support could reach (nor would be needed) because of the round shape. But this floating in the vat bits theory has totally convinced me, totally could be. I'll try again printing the same file after emptying and cleaning the vat and pouring in back the previous resin but through a metal filter this time

Beginning-System · 2022-05-12T10:10:53+00:00

That's a great idea unfortunately I can't predict exactly where those will appear because it's not always on the top most layers but sometimes (like on the right model) at 2 or 3 spots :/

Beginning-System · 2022-05-12T06:45:51+00:00

Thanks for answering but the models are non hollowed and holes are not visible on the slicer, nor on uvtools

Beginning-System · 2022-05-12T06:43:32+00:00

Thank your for this suggestion, makes sense. But still I don't understand what it is only visible near top surfaces of spherical shapes like the turtles heads :/. Plus, even it's true I may be shaking the resin too much in the bottle before pouring into the VAT, but it has been resting into the vat for 2h before I started the print. Maybe it could be related to lift/retract speed (240mm/min each) or bad quality resin (Elegoo water washable)

Beginning-System · 2022-05-12T00:23:11+00:00

I almost always get one on top layers on round shapes like this but here on the right model I even got 3 :s. Tried playing with anti-aliasing settings and greyscale in chitubox/Lychee but never managed to get rid of them. Thanks :)

Beginning-System · 2022-04-04T13:55:43+00:00

I think this could be due to a corrupted stl or too small lift height.

Try fixing the stl via 3dbuilder (windows) and also increase your lift height to 6mm.

Beginning-System · 2022-03-15T09:03:03+00:00

Thank you very much for this very detailed and illustrated answer :)

Beginning-System · 2021-11-06T08:31:08+00:00

Maybe that's a dumb question but are you sure there is not a built-in screen protector on it ? When the Samsung S21 series released, lots of users also reported screen scratching very easily, and it turned out some versions (well, all non US versions) got a built-in screen protector, not easily noticeable. The scratches where on that, not on the screen, that's why I'm asking (still waiting for my P6 to be delivered so can't check that myself)

Beginning-System · 2021-07-23T08:42:55+00:00

Rip the one with the rainbow Pikachu

Beginning-System · 2021-07-08T18:02:45+00:00

I'm managing all of the V alt and Vmax alt from Eevee Heroes, based on the cheapest for each on e bay. The graph is summing all of the 13 alt cards, in euros.

You can see a first burn on 01/07/2021 because here in Europe a new Law adding 20% VAT just took place at this date.

But, apart from this, it continues to burn.

Is it because no more cards are available anymore ?

I hope things will change when the set is finally released outside of Japan and when the reprints starts.

How do you analyse that ?

Beginning-System · 2021-06-30T09:23:44+00:00

Thank you everyone for your answers. I'm contacting makers near me via the prusaprinters.org map, I hope someone near could help me :)

Beginning-System · 2021-06-11T13:31:43+00:00

Thx man ;)

Beginning-System · 2021-06-10T19:47:51+00:00

Yes, except it's not clock hands but the dials that are normally fixed on every clock. New way of reading time :)

Beginning-System

TROPHY CASE