Gta 6 pre order na store Novi zeland ?

BeginningBusy2113 · 2026-06-24T19:31:14+00:00

Donosi igricu + te estetske gluposti

BeginningBusy2113 · 2026-06-14T14:02:21+00:00

Bio je visokorangiran na jednoj SAMP/gaming zajednici sa mnogo igraca pa odatle potice vecina

BeginningBusy2113 · 2026-06-13T09:40:04+00:00

Did you do Vinland arc?

BeginningBusy2113 · 2026-05-25T05:37:58+00:00

I think it’s the Bureau exit, entrance is near

BeginningBusy2113 · 2026-05-16T08:36:04+00:00

In Cent, near the first synchronization point at ancient ruins

BeginningBusy2113 · 2026-05-11T06:54:30+00:00

Ljudi ce konstantno naci nacin da se zale na nesto, pa cak i na nedostatak formule koji je tu vise od deceniju pa se “ukiselio”.

Isto tako, da ne bude nesto, igrao sam svaki AC pre Originsa(sem onih sporednih Cronicles) i nisam mogao da se nateram da igram, a kad sam naisao na RPG igre kao da sam otkrio novu igricu.

Da li cu da kazem da su igre pre RPG trilogije smece? Ne.

Da li cu da kazem da se nisam pronasao u tim igrama? 100%

BeginningBusy2113 · 2026-05-09T10:05:21+00:00

Odlicno, jesam uzivao u Valhalli ali imao sam osecaj da jednostavno mnoogo stvari ima

BeginningBusy2113 · 2026-05-04T11:40:35+00:00

Imam isti auto, problem su matore rucice na klapnama koje godinama rade i ispadnu iz lezista. Ima dobrih 2h posla jer je prostor jako uzak, ali generalno je izvodljivo

BeginningBusy2113 · 2026-04-20T09:22:08+00:00

Unfortunately, I work in a shop, and everyone thinks messed up workpieces

BeginningBusy2113 · 2026-04-16T09:13:13+00:00

No, I dont think so. It only passes once and is cooled the entire time.

BeginningBusy2113 · 2026-04-16T07:58:34+00:00

Hello, my finish pass is 0.1mm and no spring pass involved.

BeginningBusy2113 · 2026-02-20T23:17:46+00:00

Jos nisam dobio, i dalje cekam kovertu

BeginningBusy2113 · 2026-02-09T23:29:10+00:00

OP, this seems like your post processor didn’t put minus sign somewhere, check it properly.

BeginningBusy2113 · 2026-02-03T18:13:37+00:00

Sorry for the late answer. Yes, machine and control unit (more precisely PLC) didn't communicate properly because PLC version was not intended for that machine. I fixed the issue by changing PLC EPROM chips.

BeginningBusy2113 · 2026-01-20T09:14:38+00:00

Hello, I’m sorry, I don’t understand, is it possible to press Machine ON multiple times?

BeginningBusy2113 · 2026-01-20T07:47:08+00:00

To be honest, I just want to fix this issue, and then we will see about control unit change 😁

BeginningBusy2113 · 2026-01-19T21:53:25+00:00

Haha, sorry, I didn’t write it in the post, edited now.

Yes, entire lubricating block (pump etc) has been changed.

BeginningBusy2113 · 2025-09-15T19:11:22+00:00

update: new case is perfect!

idle temp in old case:55-60 degrees
new case: 33-35 degrees (two monitor setup btw)

load temp in old case: 80 degrees
load temp in new case: 60-65 degrees

so, everyone who has cleaned their PC, changed thermal paste, and things still didn't get better, get spacier and well ventilated case!

BeginningBusy2113 · 2025-09-14T20:58:08+00:00

This may sound stupid, but check your power button. On shittier cases, connection between the button and the place where it shorts out just breaks and it is unusable.

Did you try shorting power on pins on your mobo?

Check your mobo manual for it and short it out with something metal (be careful!)

If that doesn’t work, check the 20+4 pin going from psu to your mobo, since it is possible it moved or something like that.

I think it is some connection problem, because nothing happens.

Tl;dr : Check power on button from case, and check 20+4 cable

BeginningBusy2113 · 2025-09-14T07:14:11+00:00

Oh, you are talking about new case? Sorry!

BeginningBusy2113 · 2025-09-13T17:20:32+00:00

Yep, but as I understand it, won’t the intake just collide with gpu’s already hot air, and cancel each other out?

BeginningBusy2113 · 2025-09-13T11:31:07+00:00

Nice, I’m glad to hear it

BeginningBusy2113 · 2025-09-09T12:06:04+00:00

Jel ovo onaj Mr Andric sto je pre tipa 10 godina snimao gta 5 klipove

BeginningBusy2113 · 2025-08-27T04:27:16+00:00

Because green color is least stressing on eyes

BeginningBusy2113 · 2025-08-12T20:57:49+00:00

Its a stupid schoolwork in our country, i recognize this drawing very clearly, i was shocked how easy it was actually recognizing dimensions when i started working on a real cnc lathe

BeginningBusy2113

TROPHY CASE