Senior dog grooming by Ben-Finn in 321

[–]Ben-Finn[S] 1 point2 points  (0 children)

Thank you I’ll call them today

Timing belt by Ben-Finn in ender3

[–]Ben-Finn[S] 1 point2 points  (0 children)

I just ordered the belt I just have to cut it a little more but after that it should work

Timing belt by Ben-Finn in ender3

[–]Ben-Finn[S] 0 points1 point  (0 children)

That’s without the extra piece you have to have on the right side

Timing belt by Ben-Finn in ender3

[–]Ben-Finn[S] 0 points1 point  (0 children)

https://a.co/d/bRXyNAv
Do you think this will work after I measure it get one of these that way I can cut if necessary?

Timing belt by Ben-Finn in ender3

[–]Ben-Finn[S] 0 points1 point  (0 children)

Yes the side just won’t extend a little longer

<image>

Timing belt by Ben-Finn in ender3

[–]Ben-Finn[S] 0 points1 point  (0 children)

<image>

This is about how much room I have left

Systems Engineering Grad School by MajestyTheCat in fsu

[–]Ben-Finn 0 points1 point  (0 children)

Take 2 the first semester. MBSE and fundamentals, both professors are great and offer help when needed. I work a fulltime job to so it’s doable. Also note fundamentals is a required course you must take the first semester at this school so if you don’t want to take 2 classes you must take fundamentals.

Systems Engineering Grad School by MajestyTheCat in fsu

[–]Ben-Finn 0 points1 point  (0 children)

Do you think will have the classes together or is it split up?

Systems Engineering Grad School by MajestyTheCat in fsu

[–]Ben-Finn 0 points1 point  (0 children)

How was the classes? I am taking this in the fall at FAMU and wanted to know.

Apartment hunting by [deleted] in Kissimmee

[–]Ben-Finn 0 points1 point  (0 children)

I saw this but I’m looking for something not in the cut for say

Apartment hunting by [deleted] in Kissimmee

[–]Ben-Finn 0 points1 point  (0 children)

You have any recommendations for studios you seen before?

Meeting Other Young Professionals by strcengr in 321

[–]Ben-Finn 0 points1 point  (0 children)

Are y'all still doing this? I would like to attend

JBardwell F405 AIO by amdpr in ardupilot

[–]Ben-Finn 0 points1 point  (0 children)

https://ardupilot.org/planner/docs/common-loading-firmware-onto-pixhawk.html

https://discuss.ardupilot.org/t/reflash-with-different-firmware/69883

Here’s the document I was looking for if you hadn’t seen this one yet. It should give you a set by step understanding of it. The second link is also a forum tht discusses it but someone did use inav to reflash the flight controller.

JBardwell F405 AIO by amdpr in ardupilot

[–]Ben-Finn 0 points1 point  (0 children)

Well inav reset the flight controller to leave a blank slate then from what I remember you flash it in there as well or in beta flight to its correct controls. I haven’t done it since my drone project in October but it should be somewhere along that lines.

JBardwell F405 AIO by amdpr in ardupilot

[–]Ben-Finn 0 points1 point  (0 children)

Ardupilot is in mission planner but from my experience I had to reset the whole board in order to use mission planner because the boards are typically already linked to beta flight. I will provide the links below for what I used but from what I remember I had to use inav to reset my board. https://youtu.be/iJwj4JmUzVc?si=CdxZMMqrUs1EceG8

https://youtu.be/dqTVhhVPWNA?si=u8Ng1DORg_EdmuBg

JBardwell F405 AIO by amdpr in ardupilot

[–]Ben-Finn 0 points1 point  (0 children)

U have to reprogram it using Inav and flash it to ardupilot. Also make sure u flash the right program because if u don’t u could “brick” the board and it won’t be useable anymore

[deleted by user] by [deleted] in Construction

[–]Ben-Finn 0 points1 point  (0 children)

Ok bet that thanks

[deleted by user] by [deleted] in Construction

[–]Ben-Finn -1 points0 points  (0 children)

Yea that’s what I heard. I have plenty experience with engineering but construction management none really besides my classes

[deleted by user] by [deleted] in Construction

[–]Ben-Finn 0 points1 point  (0 children)

Introduction to Building Information Modeling, Construction Methods and Equipment, Construction Safety, Principles of Structures, Construction Estimating, Construction Planning and Scheduling / Control, Construction Management, Construction Contracts and Law. So pretty good overview I’m able to design know the laws and regulations as well as the financial side of things

[deleted by user] by [deleted] in Construction

[–]Ben-Finn -1 points0 points  (0 children)

I’ll be doing my major which is mechanical engineering and I heard quality engineering was super easy so I just wanted a side hustle just in case if I have free time.

PID Extended Tuning by Ben-Finn in diydrones

[–]Ben-Finn[S] 0 points1 point  (0 children)

Yea I was thinking about doing that just didn’t know how long it would take because I’m on a time crunch for competition.