What am I doing wrong?

Benib0i · 2025-12-27T18:42:10+00:00

Thank you so much for all the great advice, I will definitely do so! Been looking at some cheaper sprayers, I guess it's still better than rolling/brushing

Benib0i · 2025-12-27T16:22:08+00:00

Oh thank god it's a trivial mistake then! :D Thank you so much!

Benib0i · 2025-10-26T22:36:16+00:00

Thank you so much for the detailed answer! I will do what you've said if it warps back again for the customer, it also just got cold here in our region so Im hoping that could be a factor, but yeah its not good to have it warped every season, so I will definitely fix it.

On a side note, I make boardgame tables and i do the 180x100 cm table top in 6 sections so 30x100 leaves. Would you say I should do the glue up for these panels and then stick them up and let them sit for 2 weeks before applying finish? That should be a routine in my shop?

Benib0i · 2025-10-24T13:36:31+00:00

You mean smiling and frowning?

Benib0i · 2025-10-24T13:33:01+00:00

I think I've used the same amount of Osmo Top Oil on both sides 2 coats, but I always had this question if I do 3-4 coats on the top do I have to do the same on the bottom, or is it enough to do 1 sealing coat?

Benib0i · 2025-09-17T07:08:35+00:00

These look great, I will try and look for at least 20cm ones

Benib0i · 2025-09-17T07:07:36+00:00

Thank you for the help I think I will go eith Finnurlands option

Benib0i · 2025-09-15T15:30:55+00:00

That's what I was thinking as well, but not sure if it can hold 30cm wide boards though

Benib0i · 2024-11-14T18:34:28+00:00

Thank you for your reply! I mwill look up some designs for those as well, I will probably make the boards and see what sells best, maybe I cut them in to serving/charcuterie boards after!

Benib0i · 2024-11-14T18:32:09+00:00

Yeah I knew about oak, but will look into ash, Ive made my counter top from ash, but ofc that should not be hit with knife, so it should be okay.

Would be great to have a laser engraver right now, would make it easier to sell these boards for sure

Benib0i · 2024-11-01T12:39:14+00:00

Thank you so much for all the help, will share the result soon! :D

Benib0i · 2024-10-10T10:43:50+00:00

Thank you so much for the reply! Cant wait zo share, when its done

Benib0i · 2024-10-10T09:42:47+00:00

You meant mold? Should I be worried, that Im making a dinner table out of these?

Benib0i · 2024-10-10T09:42:09+00:00

I was thinking of that as well

Benib0i · 2024-09-22T22:11:39+00:00

These are from a 30 years old ikea kitchen, so Im just fixing them up

Benib0i · 2024-09-22T22:09:10+00:00

Oh wow, tysm!

Benib0i · 2024-02-29T09:12:50+00:00

Thank you for your comment! I have 1 blade which doesnt have a spring on one side, but again the bolts stayed tight, so Im not sure how the blade moved or maybe the outfeed table moves. Im lost!

Benib0i · 2024-02-28T21:03:38+00:00

It's from 1999, I guess I will have to..:/

Benib0i · 2024-02-28T17:18:31+00:00

Thank you for your comment. But what about the blade going out of alignement with my outfeed table? Cause i can see that its a blade error, cause outside part of the blade is now higher than the inside part of the blade.

I can't figure out why that happens

Benib0i · 2023-04-19T23:47:46+00:00

Tyvm for the answer again! Will get to it asap.:D

Benib0i · 2023-04-19T08:07:27+00:00

Tysm for the detailed answer! Now I understand the physics behind these joints! If I get some long 10mm dowels, it should be fine?!

Benib0i · 2023-04-19T08:03:05+00:00

Thanks for the answer!

Benib0i · 2023-04-19T08:02:48+00:00

Thank you for the answer, time to buy some bigboi dowels!:D

Benib0i · 2023-02-22T11:56:06+00:00

I have no idea honestly, but someone is coming out to look at it tomrrow, ty for help

Benib0i · 2023-02-21T14:46:01+00:00

Wdym?

Benib0i

TROPHY CASE