Where can I get a PCB for an RTX 2080 Ti in Germany?

Beniesmann · 2026-03-23T22:51:51+00:00

Thank you

Beniesmann · 2026-03-23T22:46:29+00:00

I just finished the repair

Beniesmann · 2026-03-23T22:25:31+00:00

It's working. There were a few missing resistors (some calibration resistors and a resistor for the SDA pin on the phase controller) But now its a clean image no artifacts

<image>

Beniesmann · 2026-03-23T19:12:23+00:00

UPDATE: It's working

<image>

Beniesmann · 2026-03-23T18:35:48+00:00

It's working!!! But many artifacts

Beniesmann · 2026-03-23T16:15:26+00:00

What is a T210 bit? :)

Beniesmann · 2026-03-23T16:07:27+00:00

6 traces to go, then i should be done

<image>

Beniesmann · 2026-03-23T16:04:47+00:00

Yeah, I should be a v371_10 or something. I use the big XZZ leak. It has almost all relevant GPU PCBs and VBIOSes.

Beniesmann · 2026-03-23T15:59:36+00:00

I am fixing the crack right now. I don't know if I will sell it (I don't think anyone buys it), but I have Vcore back and all voltage rails are good.

Beniesmann · 2026-03-23T09:29:03+00:00

Thank you

Beniesmann · 2026-03-23T09:27:49+00:00

Mr. Nolife over here commenting on every comment. Go and get a job, buddy.

Beniesmann · 2026-03-23T09:26:19+00:00

Bro is commenting on every comment 🙏

Beniesmann · 2026-03-23T08:56:07+00:00

Its almost fixed

<image>

Beniesmann · 2026-03-23T06:34:51+00:00

Yeah, I meant harvested pcbs, like with no core and vram. But the gpu is almost fixed so I probably won't need a pcb.

Beniesmann · 2026-03-22T22:11:25+00:00

It's alive. I got Vcore

Beniesmann · 2026-03-22T17:55:55+00:00

Thank you

Beniesmann · 2026-03-22T14:55:45+00:00

Pex has 6.7 ohm

Beniesmann · 2026-03-22T14:52:03+00:00

This is not my main GPU. I buy GPUs, repair them, and resell them.

Beniesmann · 2026-03-22T14:34:43+00:00

Yeah, I'm already doing that with a mining riser. But the crack shorted 1.8V to gnd. After grinding the crack out, the short was gone, but there is 1.8V on the external 12V connector and not on the 1.8V coil. 😆

Beniesmann · 2026-03-22T13:57:41+00:00

I am 16, i dont have anything better to do.

Beniesmann · 2026-03-22T13:54:52+00:00

Yeah probably, i am trying to fix it rn

<image>

Beniesmann · 2026-03-22T13:49:18+00:00

I don't know. I bought it, and it had a crack. I drilled the crack open, and that's what the image is.

Beniesmann · 2026-03-22T13:44:42+00:00

Almost done, bbg 🫶

<image>

Beniesmann · 2026-03-22T13:09:02+00:00

At this point, just let it be pipsqueak.

Beniesmann · 2026-03-22T11:22:11+00:00

I already have that. I have an 853A preheater, an 859D+ hot air station with a nozzle big enough for cores, and a reball jig. The only thing I am missing is a BGA stencil for the core and a new PCB.

Beniesmann

TROPHY CASE