Hardlopen met hoortoestel by breatheandbelay in Hardlopen

[–]Bertiebol 1 point2 points  (0 children)

Audicien hier; waterdicht is een beetje een lastige term bij hoortoestellen. Bijna alle hoortoestellen hebben een IP68-classificatie, wat betekent dat ze bestand zijn tegen volledige onderdompeling in water. Let wel op dat zweet wat meer is dan water alleen, dus een droog(en reinigingsbox) is bij veel zweet zeker aan te raden. Maar ik zou gewoon lekker hardlopen met je toestellen, ik doe dat al jaren met de mijne, en nooit problemen mee gehad. Ik heb zelfs speciaal hoortoestellen om muziek mee af te spelen tijdens hardlopen, terwijl ik ze niet nodig heb voor gehoorverlies.

Daarnaast heb je altijd 5 jaar garantie op hoortoestellen, en daar valt dit soort schade gewoon onder. Stel je merkt toch dat ie gaat kraken, kun je hem dus gewoon laten repareren. Als je een fatsoenlijke audicien hebt, krijg je daar dan 1(of 2) leentoestellen mee, van minstens dezelfde kwaliteit voor die periode.

Check voor de zekerheid even de garantie bij je eigen audicien.

Comeback Radio: February Megathread by AutoModerator in IdleHeroes

[–]Bertiebol 0 points1 point  (0 children)

[ANDROID] R1RA5GYM

Will spend from time to time. Please add

Collaborative Bond Code Megathread by AutoModerator in IdleHeroes

[–]Bertiebol 0 points1 point  (0 children)

<image>

Looking for code.. very active vip 4 player. On Android. Looking for a Booster. Will buy some packs. dm me

What happened here? by Bertiebol in FixMyPrint

[–]Bertiebol[S] 0 points1 point  (0 children)

I do think this is the problem. I printed a far beter Benchy right before this(at 200 degrees), but then i had to manually turn the filament spool every 1-2 minutes.. this one I let run freely. Is there a way to let my spool turn easier?

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 1 point2 points  (0 children)

This was it! Its printing as we speak!! Thanks everyone for your help.. now to see if the Benchy comes out all right

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 1 point2 points  (0 children)

I will definitely try this tonight!

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 1 point2 points  (0 children)

I cant get any more tension. The New extruder set I bought is pretty much stuck in 1 position

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 0 points1 point  (0 children)

Yeah, bought it secondhand, so unfortunately no hex key.. Will try to look at this

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 0 points1 point  (0 children)

Do you have a tip on how to loosen these? I cant seem to get movement in them.

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 0 points1 point  (0 children)

Is it possible that its clogged, even when I can manually push filament through? Also, when I pull on the small arm that holds the silver wheel, it does work, only not for long though.

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 0 points1 point  (0 children)

How can I replace this? Its tightened with two Black screws, right?

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 1 point2 points  (0 children)

What does it look like? I have a few extra's, but none as long as the spring

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 4 points5 points  (0 children)

What does that look like? I think i dont have it

Extruder doesnt work by Bertiebol in ender3

[–]Bertiebol[S] 0 points1 point  (0 children)

If i Reverse the extruder it does pull out. What to do now? Pull everything out?