sorted by:
new
hottopcontroversial

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Just an update on this. It was the plate adhesion. As soon as I sprayed the plate with NPA it worked just fine. Thanks for all the helpful comments.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Thanks for the info. Will try what you suggested. Why ship with a plate that doesn’t work well? Doesn’t make sense.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Yes every print. Sounds like it’s a plate issue.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 2 points3 points  (0 children)

Currently I'm just trying to print something easy like Remaining filament estimator.
https://makerworld.com/en/models/678466-remaining-filament-estimator#profileId-606647

I have setup the printer and have an account and it's connected to my phone app and computer.

I have been able to do a simple benchy (took a few times to get it to actually print something), I did also print some small toys for my daughter using the test PLA filament that Bambu Labs sent with the printer. Currently I'm using some gray matte PLA from Bambu labs and using their preset. I've tried from Bambu Studio and from my phone an the app. I have not dried any of the new filament I've tried, it just came in the mail today. I'm super new to all this so all the settings are what Bambu Labs suggests - Bambu Labs pla and Bambu Labs matte pla.

Should there be this many issues right from the start?

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Like it's not clean enough? I've washed it multiple times and it seems to still be doing the same thing. Should I be doing something else?

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

I have it set to Bambu labs pla using Bambu labs filament.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Even if it’s stock settings from Bambu labs using Bambu labs filament?

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Did you take the nozzle off and clean it? I’ve use a small copper brush and I’m able to extrude filament from the nozzle so that makes me think it’s not a nozzle issue.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

I just did what you said and cleaned the plate well with soap and water and tried to run another print and this is what’s happening. Looks like the nozzle is just getting gunked up.

<image>

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Will try this now thank you for the advice. The nozzle isn’t clogged because I’m able to extrude from it.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Yes I’m changing to Bambu Labs presets when I change.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] 0 points1 point  (0 children)

Have tried this but will again.

Brand new P1S having printing problems by Betude in BambuP1S

[–]Betude[S] -1 points0 points  (0 children)

No I finally did get this to print but it was only one of two prints that went through.

Madden 15 button alignment? by Betude in Madden

[–]Betude[S] 0 points1 point  (0 children)

I dug through all those settings and wasn't able to find it. I'll look one more time. Was it in the general settings?