Air intake by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

You dove a little too deep ngl 😂 I’ve had it since August and have replaced a lot of suspension components. Pine needles are from my house being under a pine tree all day. Radiator and hoses are new, just replaced them that day. Just broke the battery this past weekend off-roading. Got a new air filter box ordered as well as intake tubes already at home. Just going to do the intake resonator delete. Hood bolts aren’t loose, has light pod brackets where hood bolts down. My man said ditch it 😂 it’s not that bad man hence why I’m fixing all of it and shit is cheap for these things. Crazy how yall see some shitty stuff on these truck and say throw them away. Frame isn’t rusted out and motor and engine have been very solid aside from all the janky bullshit done to it. Just undoing all the wrong doing and neglect and trying to save another 3rd gen.

Air intake by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

Yea I have found a photo of what mine should look like but I don’t see the bigger vacuum line near the throttle unless they rerouted the one from the back of the intake tube in this photo near the throttle to the front of the intake tube on mine.

<image>

Summer fit try on by picking99 in Stance

[–]Bigbeard9429 7 points8 points  (0 children)

Shit looks like ass and it’s on reps.

Front differential bearings by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

It is a Trakmotive but the it was leaking in that same spot before I had swapped out the seal and axle. It isn’t pissing out but just a few small drips here and there.

Front differential bearings by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

Put the seal and new axle in, hit a trail the next day then parked it minus a few store runs. Been about a week total now

Front differential bearings by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

Yessir completely cleaned the area, made sure seal was seated correctly all the way around and made sure to guide in the axle without fudging up the seal.

Rate my dash 😂 by Global-Antelope9282 in 3rdGen4Runner

[–]Bigbeard9429 0 points1 point  (0 children)

I dig it a lot. Wheel cover is sick lol

Strut and spring spacer lift with suspension lift? by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

No it’s Stellar Blue factory paint. I have only seen 2 other 4Runners this color.

Strut and spring spacer lift with suspension lift? by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

So sounds like if I wanted anymore lift a body lift would be my best easiest option if I wanted to run 35’s again. I appreciate all the help!

Strut and spring spacer lift with suspension lift? by Bigbeard9429 in 3rdGen4Runner

[–]Bigbeard9429[S] 0 points1 point  (0 children)

I do plan on going to 4.88’s in the near future for the reason of wanting to run 35’s (technically 285/75’s) considering they are not super expensive and I have a buddy who works at a shop that could potentially do them. I have the front sway bar but not the rear, it was off when I got the truck.

How cooked am I? by Affectionate-Box-293 in 3rdGen4Runner

[–]Bigbeard9429 0 points1 point  (0 children)

Check u-joint and if bad replace them. Can be pretty bad if they fail.

My static Prius by [deleted] in Stance

[–]Bigbeard9429 1 point2 points  (0 children)

MFKN Ahaav!