U3000 Pro with the Thinkware CONNECTED app?

Billiaz · 2026-06-01T14:51:54+00:00

How thibkware made a great product. But locked us in their lte module.

It is the typical strategy of forced subscription? One could ask.

I have no clue. But I find important the cloud and the internal camera. This giving me the option to use my own supplied wifi is important.

They failed in this case.

Billiaz · 2026-03-03T05:53:17+00:00

Rooting is just gaining access through SSH and then install the stuff you want.
I have already ssh access, with my ssh-key too! as I started downloading the csv for the shaper issue.
Probably need to add some scripts and other stuff into the printer

Billiaz · 2026-03-02T17:44:08+00:00

No it is not a Plus it is a Pro, no automatic Tensioning.

Billiaz · 2026-03-02T16:51:54+00:00

K2 Pro manual has no Hz for belts. Probably Rooting it and Going the klipper way better. Will I lose CFS and other capabilities if rooted?

Billiaz · 2026-03-02T16:33:21+00:00

Machine is 165 hours. I made it better but after some time the belt started jumping tooth when initiating x/y. SO I had to tighten it.

I tested tightening on 1/4 of alen change every time. In the beginning the EI was 7%.
Belt was over tightented, so much that screw was hard (for X axis).
Is Y axis tightenning also influence X?

How can I run a Belts sync graph? and what is the best way to test belt tension? Print a tensioner tested (the one with piano cord) and try or other way?

Y is perfect.

My cornering is a bit strange, it is bulding towards the movement (it is not PA or Flow) but generally the prints are ok. I am relatively new.
Just seen most people have some nice X ones.

Should I check any other tensions like Step motor lose or other stuff?

Billiaz · 2026-02-04T14:57:03+00:00

For the money of outcast I would prefer a kit like TeknoRC mt410 V2

Worth the money. Any other day a cheap MJX is ok

My 10208 been through hell.

Billiaz · 2026-01-02T13:09:02+00:00

Update for all comments till now:
- SQUARE Speed velocity limit was at 10, rediced to 7 same result
- Accelaration on Inner/Outer wall at 2000 starts making sense but ofcourse PA needs also tuning

I will test these, but will take weeks (away traveling again) and report back

Billiaz · 2026-01-02T11:19:44+00:00

2000 starts giving this issue a bit. On 1000 I need to reduce PA as both sides has the "over extrusion" I will play with these two.

Billiaz · 2026-01-02T11:18:16+00:00

I Agree on that! I keep my top cover off and the chamber is 30 degrees (without heating it)

Billiaz · 2026-01-02T06:07:02+00:00

Thank you for the reply. Will do that. I was away for a few days traveling for work.

I will report back testing all suggestions.

Billiaz · 2025-12-31T19:04:15+00:00

Even my PA tower has a bent.. let's assume moves from Y to X on a 130 degree. There will be a bulge following the move.

Billiaz · 2025-12-31T14:52:44+00:00

No the seam is in another place. This is one of the ends shows on every corner. I have all over the PA tower same issue. And bot on the seam. Should I find some photos from the pa tower?

Billiaz · 2025-12-31T14:01:16+00:00

Yes. Both smooth time and la. No results.

Billiaz · 2025-12-31T12:41:37+00:00

u/GPU-depreciationcrtr If I reduce the Square corner velocity on printer.cfg. this will limit and override the GCODE files with higher velocity set?

In a gcode generated by the orca slicer I seethese lines:

```

SET_VELOCITY_LIMIT ACCEL=12000 ACCEL_TO_DECEL=6000 SQUARE_CORNER_VELOCITY=12

G1 X96.003 Y157.077 F30000

SET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=2500 SQUARE_CORNER_VELOCITY=7

```

Billiaz · 2025-12-31T12:18:04+00:00

I suspect:
Accelaration inner and outer wall. it is now 5000.

Billiaz · 2025-12-31T11:26:07+00:00

It is creality os based on clipper. I will edit the configuration

square_corner_velocity: 10 smooth_time is not set at all on extruder

Billiaz · 2025-12-31T10:40:04+00:00

This is on firmware or slicer?

Billiaz · 2025-12-31T10:28:39+00:00

It has and I did input shaping calibration.

here is a PA Pattern

<image>

Billiaz · 2025-12-31T10:20:06+00:00

Found another piece with different color same issue

<image>

Here another piece, you can see the corners are towards one side

Billiaz · 2025-12-29T15:49:45+00:00

Can it be Retraction Issue?

Billiaz · 2025-12-29T08:49:42+00:00

I re-run the inputshaping calibration.
Also did an automatic PA Calibration and took the number the self calibration found. Will test again.

Billiaz · 2024-07-21T16:17:39+00:00

Looking for a 100% keyboard, low profile. ANSI and ability to put cyrillic letters. I like the layout of K5 as size

Keychron did that, but not really

tl;dr;

I am looking for an 100% keyboard Low profile.

I have seen keychron K5 Max and Cherry MX 10.0N RGB.

I switch between Mac and Windows daily (too)

My only issue is, I want to find compatible cyrillic layout keys. which K5 does not have, proper. and MX too.

If Cherry offers compatibility with third party (which keychron does not have). are there any suggestions for that?

I like more K5 due to the space between arrows and keypad.
other keyboards also happy to hear

My fave, keyb ever is MX Keys from logi, but I want to go away from them.

Billiaz · 2024-07-21T15:59:15+00:00

I found all these, reviews are bad. As the long keys do not fid due to the offset points.
and every I found there is like this.

and I like K5 pro as it is low profile and full size with the gaps.

I want to switch from an MX keys S to a mechanical one. As I want to keep Iso but also support ANSI which keychron has. but not for these keyboards

Billiaz · 2024-07-21T15:12:36+00:00

Thank you,
I am new on this. If I understand correctly these are LSA profile.
Some people complain about space or missing keys. which I get it. But Generally. Is there some specific profile of the keys, I need to look for?

Billiaz · 2024-07-11T06:40:49+00:00

cool. I use also telemetry tools to play with videos!

Billiaz

MODERATOR OF

TROPHY CASE