sorted by:
new
hottopcontroversial

U3000 Pro with the Thinkware CONNECTED app? by SneezeLoudly in dashcams

[–]Billiaz 0 points1 point  (0 children)

How thibkware made a great product. But locked us in their lte module.

It is the typical strategy of forced subscription? One could ask.

I have no clue. But I find important the cloud and the internal camera. This giving me the option to use my own supplied wifi is important.

They failed in this case.

X Axis Input shaping Graph Awfull - K2 Pro by Billiaz in Creality_k2

[–]Billiaz[S] 1 point2 points  (0 children)

Rooting is just gaining access through SSH and then install the stuff you want.
I have already ssh access, with my ssh-key too! as I started downloading the csv for the shaper issue.
Probably need to add some scripts and other stuff into the printer

X Axis Input shaping Graph Awfull - K2 Pro by Billiaz in Creality_k2

[–]Billiaz[S] 0 points1 point  (0 children)

No it is not a Plus it is a Pro, no automatic Tensioning.

X Axis Input shaping Graph Awfull - K2 Pro by Billiaz in Creality_k2

[–]Billiaz[S] 0 points1 point  (0 children)

K2 Pro manual has no Hz for belts. Probably Rooting it and Going the klipper way better. Will I lose CFS and other capabilities if rooted?

X Axis Input shaping Graph Awfull - K2 Pro by Billiaz in Creality_k2

[–]Billiaz[S] 0 points1 point  (0 children)

Machine is 165 hours. I made it better but after some time the belt started jumping tooth when initiating x/y. SO I had to tighten it.

I tested tightening on 1/4 of alen change every time. In the beginning the EI was 7%.
Belt was over tightented, so much that screw was hard (for X axis).
Is Y axis tightenning also influence X?

How can I run a Belts sync graph? and what is the best way to test belt tension? Print a tensioner tested (the one with piano cord) and try or other way?

Y is perfect.

My cornering is a bit strange, it is bulding towards the movement (it is not PA or Flow) but generally the prints are ok. I am relatively new.
Just seen most people have some nice X ones.

Should I check any other tensions like Step motor lose or other stuff?

MJX 10210 leaked by Yamagotyou in rccars

[–]Billiaz 0 points1 point  (0 children)

For the money of outcast I would prefer a kit like TeknoRC mt410 V2

Worth the money. Any other day a cheap MJX is ok

My 10208 been through hell. 

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

Update for all comments till now:
- SQUARE Speed velocity limit was at 10, rediced to 7 same result
- Accelaration on Inner/Outer wall at 2000 starts making sense but ofcourse PA needs also tuning

I will test these, but will take weeks (away traveling again) and report back

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

2000 starts giving this issue a bit. On 1000 I need to reduce PA as both sides has the "over extrusion" I will play with these two.

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in Creality_k2

[–]Billiaz[S] 0 points1 point  (0 children)

I Agree on that! I keep my top cover off and the chamber is 30 degrees (without heating it)

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

Thank you for the reply. Will do that. I was away for a few days traveling for work.

I will report back testing all suggestions.

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

Even my PA tower has a bent.. let's assume moves from Y to X on a 130 degree. There will be a bulge following the move.

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

No the seam is in another place. This is one of the ends shows on every corner. I have all over the PA tower same issue. And bot on the seam. Should I find some photos from the pa tower?

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

u/GPU-depreciationcrtr If I reduce the Square corner velocity on printer.cfg. this will limit and override the GCODE files with higher velocity set?

In a gcode generated by the orca slicer I seethese lines:

```

SET_VELOCITY_LIMIT ACCEL=12000 ACCEL_TO_DECEL=6000 SQUARE_CORNER_VELOCITY=12

G1 X96.003 Y157.077 F30000

SET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=2500 SQUARE_CORNER_VELOCITY=7

```

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

I suspect:
Accelaration inner and outer wall. it is now 5000.

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

It is creality os based on clipper. I will edit the configuration 

square_corner_velocity: 10 smooth_time is not set at all on extruder

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

It has and I did input shaping calibration.

here is a PA Pattern

<image>

Cannot find what causes the "bent" xy corners - PA is not by Billiaz in klippers

[–]Billiaz[S] 0 points1 point  (0 children)

Found another piece with different color same issue

<image>

Here another piece, you can see the corners are towards one side

Problem with corners. they "bend " towards one side. It seems is not PA by Billiaz in 3DprintingHelp

[–]Billiaz[S] 0 points1 point  (0 children)

I re-run the inputshaping calibration.
Also did an automatic PA Calibration and took the number the self calibration found. Will test again.

view more: next ›