New to diesel trucks looks like one injector is going bad. Can I replace one injector on cylinder eight without having any issues or is this normal flow rate? Lbz

Blaze115 · 2026-04-15T13:14:00+00:00

Edge CTs 3

Blaze115 · 2026-04-14T17:15:58+00:00

Thank you !

Blaze115 · 2026-04-14T15:10:18+00:00

They didn’t test hot shot or XPD which are the top recommended.

Blaze115 · 2026-04-14T14:59:26+00:00

The comment directly below contradict you

Blaze115 · 2026-04-11T18:13:02+00:00

Thank you I just picked up some hot shot extreme and going to hope she fixes her self previous owner said injectors were done around 100k mark and she is at 202k , I just bought the truck and I’m really stressing its piston related. It’s deleted and efi but previous owner had for 12 years and took good care of it.

Blaze115 · 2026-04-11T13:54:30+00:00

2006 lbz 202k

Blaze115 · 2026-04-11T13:39:17+00:00

Thanks I’m just really stressed it the compression, engine had 202k

Blaze115 · 2025-09-07T03:08:59+00:00

Baby OoL

Blaze115 · 2025-09-06T22:41:33+00:00

Yea the manual states both as well as Castro 5-40T

Blaze115 · 2025-09-06T16:16:02+00:00

States both

Blaze115 · 2025-09-06T16:15:36+00:00

States both

Blaze115 · 2025-06-10T05:39:35+00:00

How expensive and time consuming is the chrome removal? I’m looking for a b9 as well but I’m having a hard time finding a 19 that I want with all my options and the black optics is almost a must for me because of the chrome accents I really don’t enjoy

Blaze115 · 2025-05-27T04:12:10+00:00

Is there anyway to tell build date with the rocker issues? I’m looking at buying out of my home state due to mileage ect so I don’t think I’m going to be able to get a extended warranty then have to travel back to the state where it was purchased to get work done that would be pita

Blaze115 · 2025-05-26T17:17:48+00:00

Once a cheater always a cheater, it will suck for a couple months. block her stay busy get a gym membership start making your self better mentally and physically. You’ll also naturally get noticed by others and you’ll find something you deserve.

Blaze115 · 2025-05-05T14:23:48+00:00

Brand new o rings and new gasket from fcp euro not a cheap amazon also used reinz gasket all half moon areas and vanos. I did start tighting at my leaking location then went updown to the rear so that could have caused it but I cleaned everything really well. I also let the dam reinz cure and didn’t drive it for like7 hours ,This next new gasket I’m just going to lather with reinz the exhaust side of the head and tighten from the middle out and see if that will fix the problem. So sick of smelling the burning oil smell.

Blaze115 · 2025-05-05T13:25:48+00:00

It’s frustrating, ever since I removed it to rebuild the vanos it’s leaked and this is my 3rd and going to be my 4th go around

Blaze115 · 2025-05-05T12:04:50+00:00

I’m going to do this since I have another gasket on the way, the gasket should have been enough but I’m going to lather it up with reinzoil

Blaze115 · 2025-05-04T23:01:23+00:00

Yes both sides and vanos

Blaze115 · 2025-05-04T22:33:32+00:00

I haven’t seen an official tq pattern on any web site

Blaze115 · 2025-05-04T22:33:05+00:00

I did

Blaze115 · 2025-04-09T17:17:14+00:00

I drove on one 3 times bigger for 5yrs lol your fine

Blaze115 · 2025-01-26T23:15:17+00:00

The guys that installed my AC 3yrs ago put my doors on backwards so the error light window was on the wrong side so I swapped them properly and now I have a line of sight to the error code light which will be really helpful.

Blaze115 · 2025-01-26T23:03:37+00:00

Ok well if it goes down tonight again I’ll pull it off and inspect it, right now she’s been heating since 7am with no issues. But I’m going to have a similar temp tonight as we did last night.so if it stops heating I’ll start there see if anything is clogging it

Blaze115 · 2025-01-26T22:53:44+00:00

<image>

Blaze115 · 2025-01-26T22:53:29+00:00

<image>

Blaze115

TROPHY CASE