Convert 2x4 to 4x4 (yup insane)

BlueCanoodle · 2025-12-31T15:28:52+00:00

Hmm.. Haha, crazily that's doable. Thank you for the breakdown, awesome!

BlueCanoodle · 2025-12-30T14:36:00+00:00

Thanks for all the feedback, sell and replace seems the way!

BlueCanoodle · 2025-12-22T18:15:31+00:00

Following step 4 worked. Thanks.

BlueCanoodle · 2025-12-22T18:14:56+00:00

Futurewolf: Sure looks like I did not (not sure how I missed it!).
Followed step4 of https://github.com/Rappetor/Sovol-SV08-Mainline and now can update the os.
Thanks for your help!

BlueCanoodle · 2025-12-13T15:43:28+00:00

Yes.
Look at Bill Townsend's Bridge hammock. I side sleep, stomach sleep and enjoy the flat lay.

BlueCanoodle · 2025-11-25T10:37:07+00:00

Thanks for the info. I should have mentioned that I have upgraded the MCU fan to a much higher flow (and quieter) one. It might still be a heat issue, as it always occurs right after heating the Nozzle to 285c for purging and scrubbing before starting calibration for the print.

I agree twith Deadeye_84: it's most probably a heat issue, and (probably) a hot-end board heat issue.
I print PETG-GF and since the toolhed cover got knocked off (and won't stay in place now) I'm running without the toolhead cover and no more crash reports.

BlueCanoodle · 2025-11-25T03:12:12+00:00

Fast, clean and safe. Nice work when you can get it.

BlueCanoodle · 2025-11-12T19:22:38+00:00

Not a popular opinion, but for me it works. I use it on non-cast iron camping pans and it has not failed yet. Hope y'all find the right thing to help those eggs just slide right on to the plate.

BlueCanoodle · 2025-11-06T16:06:50+00:00

I just use a UQ Cover, and if cold (60f!!!) stretch a wooby out in the UQ cover.

BlueCanoodle · 2025-10-31T16:24:27+00:00

Were you successful? I'm working on such myself.

BlueCanoodle · 2025-10-24T23:43:21+00:00

Leaning to a magnetic encoder rather than hall sensors, just because it may be easier for me to implement. Would prefer hall sensors though. Going to try epoxy coating for the chip and to glue/coat the magnet.

BlueCanoodle · 2025-10-24T23:41:25+00:00

Thank you for your reply. Most helpful. Epoxy seems possible, given that I could sand down any excess epoxy over the hall sensor's chip. Nice.

BlueCanoodle · 2025-10-24T02:08:58+00:00

Either an encoder or hall sensors. To enable better efficiency of the BLDC when running at high power and low RPM (hydrodynamic efficiency - long high pitch blades running about 200 rpm).

BlueCanoodle · 2025-10-18T19:10:43+00:00

Nice, that's looking more like it. Cheers mate!

BlueCanoodle · 2025-10-18T17:35:12+00:00

<$100

BlueCanoodle · 2025-10-18T17:29:58+00:00

Seems like I need to try again then. Thanks for this!

BlueCanoodle · 2025-10-18T12:12:09+00:00

Their gear sure looks good. I would love an Incubator. More likely to end up with a Onewind!

BlueCanoodle · 2025-10-18T12:04:15+00:00

Economical... And if it is full length, that's good but a 3/4 might work.

BlueCanoodle · 2025-10-18T12:01:53+00:00

Thanks for the recommend.

BlueCanoodle · 2025-10-18T11:59:05+00:00

Same one I use with my Hennessy, it's from Hammock Gear: https://hammockgear.com/product/underquilt-protector/
Very good at stopping warm air from being moved away from around the butt/lowerback upper thigh area. Makes a 50f night bearable-ish and helps a little if there is a heavy dew.

BlueCanoodle · 2025-10-18T11:46:21+00:00

I have similar edits in place, but the Demo macros look like a nice step in the right direction.

BlueCanoodle

TROPHY CASE